Kenmore 6703 Use and Care Guide - Page 17

If the dryer will not start, If you do not feel heat, turn off the dryer and check, following

Get Kenmore 6703 - Elite Oasis 7.0 cu. Ft. Capacity Flat Back Electric Dryer PDF manuals and user guides View all Kenmore 6703 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 17 highlights

3. Remove the 4 screws from the opposite side of the door. 6= Hang door by placing screw heads into top slotted holes of hinges and slide door down. Align bottom screw holes in hinge and door. Install two bottom screws. Tighten all hinge screws. I I 4. Install the 2 hinges to the front panel of the dryer using 4 screws. Use the non-slotted side to attach the hinge to the front panel. 5. Install screws in the top hinge holes in the door. Do not tighten screws. Leave approximately W' (5 mm) of screw exposed. A. Install these screws first. 7. Close door to engage door strike. ©@' Sp el_{!} 1. Check that all parts are now installed. If there is an extra part, go back through the steps to see which step was skipped. 2. Check that you have all of your tools. 3. Dispose of/recycle all packaging materials. 4. Check the dryer's final location. Be sure the vent is not crushed or kinked. 5. Check that the dryer is level. See "Level Dryer." 6. For power supply cord installation, plug into an outlet. For direct wire installation, turn on power. 7. Remove any protective film or tape remaining on the dryer. NOTE: Glass door models have a protective film on the window that should be removed. 8. Read "Dryer Use." 9. Wipe the dryer drum interior thoroughly with a damp cloth to remove any dust. f0. Test dryer operation by selecting a Timed Dry heated cycle and starting the dryer. For this test, do not select the Air Only modifier. If the dryer will not start, check the following: • Controls are set in a running or "On" position. • Start button has been pushed firmly. • Dryer is plugged into an outlet and/or electrical supply is on. • Household fuse is intact and tight, or circuit breaker has not tripped. • Dryer door is closed. 11. When the dryer has been running for 5 minutes, open the dryer door and feel for heat. If you feel heat, cancel cycle and close the door. If you do not feel heat, turn off the dryer and check the following: • There may be 2 household fuses or circuit breakers for the dryer. Check that both fuses are intact and tight, or that both circuit breakers have not tripped. If there is still no heat, contact a qualified technician. NOTE: You may notice an odor when the dryer is first heated. This odor is common when the heating element is first used. The odor will go away. 17

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
3.
Remove the 4 screws
from the opposite
side of the door.
I
I
4.
Install the 2 hinges to the front
panel of the dryer using
4 screws.
Use the non-slotted
side to attach
the hinge to the
front panel.
5.
Install screws
in the top hinge holes in the door. Do not
tighten
screws.
Leave approximately
W'
(5 mm) of screw
exposed.
A. Install these screws
first.
6=
Hang door by placing screw heads into top
slotted
holes of
hinges and slide door down. Align bottom
screw
holes in
hinge and door. Install two bottom
screws.
Tighten
all hinge
screws.
7.
Close door to engage door strike.
©@' Sp el_{!}
1.
Check that all parts are now installed.
If there is an extra part,
go back through
the steps
to see which step was skipped.
2.
Check that you have all of your tools.
3.
Dispose
of/recycle
all packaging
materials.
4.
Check the dryer's final location.
Be sure the vent is not
crushed
or kinked.
5.
Check that the dryer is level. See "Level Dryer."
6.
For power supply
cord installation,
plug into an outlet.
For
direct wire installation,
turn on power.
7.
Remove
any protective
film or tape remaining
on the dryer.
NOTE: Glass door models
have a protective
film on the
window
that should be removed.
8.
Read "Dryer Use."
9.
Wipe the dryer drum
interior thoroughly
with a damp cloth to
remove any dust.
f0.
Test dryer operation
by selecting
a Timed
Dry heated cycle
and starting
the dryer. For this test, do not select the Air Only
modifier.
If the dryer will not start,
check
the following:
11.
•
Controls
are set in a running
or "On" position.
•
Start button
has been pushed firmly.
•
Dryer is plugged
into an outlet and/or
electrical
supply
is on.
•
Household
fuse is intact
and tight, or circuit breaker
has
not tripped.
•
Dryer door is closed.
When the dryer has been running
for 5 minutes, open the
dryer door and feel for heat. If you feel heat, cancel
cycle and
close the door.
If you do not feel heat, turn off the dryer and check
the
following:
•
There may be 2 household
fuses or circuit
breakers
for
the dryer. Check that both fuses are intact
and tight,
or
that both circuit
breakers
have not tripped.
If there is still
no heat, contact
a qualified
technician.
NOTE: You may notice an odor when the dryer is first
heated.
This odor is common
when the heating element
is first used. The
odor will go away.
17