Kenmore 6703 Use and Care Guide - Page 22

You can customize your cycles by selecting OPTIONS options. Q ADUaTmOpCt DS',r0yt¥Signal Wrinkle Guard 60 Damp Dry Signal Select the Damp Dry Signal to alert you that your clothes are approximately 80% dry or suitable for ironing. This is useful when you want to remove lightweight items in a mixed load to avoid overdrying or remove partially dry items that may need ironing. The DAMP DRY SIGNAL is useful when drying bedsheets/linens in a mixed load. When the signal goes off, open the door to stop the dryer, rearrange the load inside the dryer, close the door and restart the dryer to finish the drying cycle. Rearranging the load will aid in the drying process. NOTE: The Damp Dry Signal is available only with the Auto Dry Cycles. WRINKLE GUARD _}(30, 60, 90, 150 minutes) WRINKLE GUARD _ helps smooth out wrinkles that may form when clothes are not removed promptly at the end of a cycle. During this option, the dryer stops tumbling and then tumbles again for a brief period without heat when pressed. • Press WRINKLE GUARD ®to get heat-free, periodic tumbling at the end of a cycle. WRINKLE GUARD _ periodically starts and stops the dryer, tumbling the load without heat for 30, 60, 90 or 150 minutes (depending on your model) unless you open the dryer door. • Stop WRINKLE GUARD ® at any time by pressing WRINKLE GUARD ®, opening the dryer door or pressing STOR • For the Casual Cycle, WRINKLE GUARD ® is preset to ON. The other Auto Dry Cycles will retain the WRINKLE GUARD ® setting. For example, if you select WRINKLE GUARD ® in the Normal cycle, WRINKLE GUARD ®will be on the next time you select the Normal cycle. NOTE: If you do not select WRINKLE GUARD _, the dryer stops after cool down. Cycle Signal The Cycle Signal produces an audible sound when the drying cycle is finished. Promptly removing clothes at the end of the cycle reduces wrinkling. Press CYCLE SIGNAL to turn the Cycle Signal On or Off. On Off Cycle Signal NOTE: When WRINKLE GUARD _ is selected, a tone sounds every 5 minutes until the clothes are removed, or WRINKLE GUARD _ ends. You can change Auto and Timed Cycles, Modifiers and Options anytime before pressing Start. • Three short tones sound if an unavailable combination is selected. The last selection will not be accepted. Changing Cycles after pressing Start 1. Press STOP twice. 2. Select the desired cycle and options. 3. Press START. The dryer starts at the beginning of the new cycle. NOTE: If you do not press Start within 5 minutes of selecting the cycle, the dryer automatically shuts off. Changing Modifiers and Options after pressing Start You can change a Modifier or Option anytime before the selected Modifier or Option begins. 1. Press STOP once. 2. Select the new Modifier and/or Options. 3. Press START to continue the cycle. NOTE: If you happen to press STOP twice, the program clears and your dryer shuts down. Restart the selection process. Changing the Preset Dryness Level Settings If all your loads on all Auto Dry cycles are consistently not as dry as you would like, you may change the preset Dryness Level settings to increase the dryness. This change will affect all of your Auto Dry cycles. Your Dryness Level settings can be adjusted to adapt to different installations, environmental conditions or personal preference. There are 3 drying settings: 1 (factory preset dryness level), 2 (slightly dryer clothes, approximately 15% more drying time) and 3 (much dryer clothes, approximately 30% more drying time). 1. The Dryness Level settings cannot be changed while the dryer is running. 2. Press and hold the Dryness Level button for 5 seconds. The dryer will beep, and "CF" will be displayed for 1 second followed by the current drying setting. 3. To select a new drying setting, press the Dryness Level key again until the desired drying setting is shown. NOTE: While cycling through the settings, the current setting will not flash, but the other settings will flash. 4. Press START to save the drying setting. 5. The drying setting you selected will become your new preset drying setting for all Auto Dry cycles. 22