Kenwood DNX571HD User Manual - Page 97

Security setup, EXT SW setup DNX891HD, DNX7710BT, Return to the Top

Get Kenwood DNX571HD PDF manuals and user guides View all Kenwood DNX571HD manuals
Add to My Manuals
Save this manual to your list of manuals

Page 97 highlights

Return to the Top page Setting Up Security setup A red indicator will blink on the unit after the ACC is set to OFF, warning potential thieves. If turned to "ON" (default), the security indicator on the front panel flashes when the vehicle ignition is off. 1 Touch [Security] in the System Menu screen. Security screen appears. 2 Touch [ON] or [OFF] of [SI]. EXT SW setup (DNX891HD, DNX7710BT) Set up the external switch power mode. 1 Touch [EXT SW] in the System Menu screen. EXT SW screen appears. 2 Set each item as follows. SW Name Sets the name of the external device. Output Pattern Sets the power signal output mode among "Pulse"/"Level". Default is "Pulse". You can set to turn output on/off each time the button on the EXT SW screen is touched. See External Device Control (P.104). Pulse Set Sets the pulse signal output time. Outputs 500ms when "1" is set. Increases by 200ms with each step. Up to 100 steps can be set. NOTE • You can enter characters only after you have applied the parking brake. • "Pulse": Generates a single power signal pulse. • "Level": Continues output of high power signal. 96

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
96
96
Return to the Top page
Setting Up
Security setup
A red indicator will blink on the unit after the
ACC is set to OFF, warning potential thieves.
If turned to “ON” (default), the security
indicator on the front panel flashes when the
vehicle ignition is off.
1
Touch [Security] in the System Menu
screen.
Security screen appears.
2
Touch [ON] or [OFF] of [SI].
EXT SW setup (DNX891HD,
DNX7710BT)
Set up the external switch power mode.
1
Touch [EXT SW] in the System Menu
screen.
EXT SW screen appears.
2
Set each item as follows.
SW Name
Sets the name of the external device.
Output Pattern
Sets the power signal output mode among
“Pulse”/“Level”. Default is “Pulse”.
You can set to turn output on/off each time
the button on the EXT SW screen is touched.
See
External Device Control (P.104)
.
Pulse Set
Sets the pulse signal output time.
Outputs 500ms when “1” is set.
Increases by 200ms with each step. Up to 100
steps can be set.
NOTE
• You can enter characters only after you have
applied the parking brake.
• “Pulse”: Generates a single power signal pulse.
• “Level”: Continues output of high power signal.