Kenwood KDC-X696 Instruction Manual

Kenwood KDC-X696 Manual

Get Kenwood KDC-X696 PDF manuals and user guides View all Kenwood KDC-X696 manuals
Add to My Manuals
Save this manual to your list of manuals

Kenwood KDC-X696 manual content summary:

  • Kenwood KDC-X696 | Instruction Manual - Page 1
    KDC-BT652U KDC-X696 CD-RECEIVER INSTRUCTION MANUAL AMPLI-TUNER LECTEUR DE CD MODE D'EMPLOI REPRODUCTOR DE DISCOS COMPACTOS RECEPTOR DE FM/AM MANUAL DE INSTRUCCIONES Take the time to read through this instruction manual. Familiarity with installation and operation procedures will help you obtain the
  • Kenwood KDC-X696 | Instruction Manual - Page 2
    Preparation 4 How to attach/detach the faceplate How to reset your unit How to prepare the remote controller (RC-405) Getting Started 5 Canceling the display demonstration Setting the demonstration mode Adjusting the clock Initial settings before operations Basic Operations 6 Listening
  • Kenwood KDC-X696 | Instruction Manual - Page 3
    this manual are faceplate) ■■The "AAC" logo is a trademark of Dolby Laboratories. ■■The Bluetooth word mark and logos are owned by the Bluetooth SIG, Inc. and any use of such marks by JVC KENWOOD Corporation is under license. Other trademarks and trade names are those of their respective owners
  • Kenwood KDC-X696 | Instruction Manual - Page 4
    do not touch the terminals of the unit and faceplate with your fingers. How to reset your unit If this unit fails to operate properly, press the reset 1 button. 2 The unit returns to the factory settings when the reset button is pressed. 3 Reset button If the effectiveness of the remote controller
  • Kenwood KDC-X696 | Instruction Manual - Page 5
    knob to enter [FUNCTION] mode. 2 Turn the volume knob to select [SETTINGS], then press to enter. 3 Turn the volume knob to select [CLOCK], then press to enter. 4 Turn the volume knob to select [CLOCK ADJUST], then press to enter. Clock hour flashes on the display. 5 Turn the volume knob to adjust
  • Kenwood KDC-X696 | Instruction Manual - Page 6
    Detaches the faceplate The following indicator lights up when... ST: A stereo broadcast is received. RDS: Radio Data System service is available. TI: Traffic Information function is turned on. IN: A disc is in the unit. ATT: The sound attenuates. EQ: [PRESET EQ] is set to an EQ mode other than
  • Kenwood KDC-X696 | Instruction Manual - Page 7
    directly (page 5) if pressed and held while in clock display screen. ■■Enters Bluetooth mode. (page 18) ■■Press to answer an incoming call. - Enters Bluetooth pairing mode if pressed and held. (page 16) - AUD Enters [AUDIO CONTROL] settings directly. - ATT Attenuates the sound. • To return
  • Kenwood KDC-X696 | Instruction Manual - Page 8
    band. 4 / +¢ 1 - 6 : Selects station. : Selects preset station. Adjust [SETTINGS] mode settings While listening to the radio... 1 Press the volume knob to enter [FUNCTION] mode. 2 Turn the volume knob to select [SETTINGS], then press to enter. 3 Turn the volume knob to make a selection, then
  • Kenwood KDC-X696 | Instruction Manual - Page 9
    source is selected, these settings are selectable under [TUNER SET] item. (page 25) Data System feature won't work where the service is not supported by any broadcasting station. ■■If the Turn on the external component and start playing. 3 Turn the volume knob to adjust the volume. Portable audio
  • Kenwood KDC-X696 | Instruction Manual - Page 10
    resume playback. Press to select folder of Audio File/iPod. Start playing a disc 1 Press SRC to turn on the power. 2 Insert a disc "PANDORA". 2 Remove the USB device or iPod. Selecting Repeat Play Press number button 4 (REP) repeatedly to make a selection. Audio CD : TRACK REPEAT, REPEAT OFF Audio
  • Kenwood KDC-X696 | Instruction Manual - Page 11
    only for the iPod or KENWOOD Music Editor media. ■■To return to the root folder (audio file), top menu (iPod) or first track (audio CD), press 5. ■■To return to the previous folder, press . ■■To cancel the Music Search mode, press and hold . ■■< or > on the display indicates that preceded/next item
  • Kenwood KDC-X696 | Instruction Manual - Page 12
    on the display. MODE OFF: Control iPod from the unit. * You can still control play/pause, select files, fast- forward/reverse files from the unit. Adjust [SETTINGS] mode settings While listening to an iPod or KENWOOD Music Editor media ... 1 Press the volume knob to enter [FUNCTION] mode. 2 Turn the
  • Kenwood KDC-X696 | Instruction Manual - Page 13
    ver1.1" or later. ■■When you use the audio file with database information added by the "KENWOOD Music Editor Light ver1.1", you can search for a file by title, album or artist name using the function mentioned in Music Search (page 11). ■■In the Instruction manual, the term "Music Editor media" is
  • Kenwood KDC-X696 | Instruction Manual - Page 14
    iPhone 1 Press SRC to select a source other than "PANDORA" or "iPod". 2 Remove the iPhone. Station Search mode While listening to "PANDORA" source... 1 Press to enter Station Search mode. 2 Turn the volume knob to select [A-Z] (stations are displayed in alphabetical order) or [BY DATE] (stations are
  • Kenwood KDC-X696 | Instruction Manual - Page 15
    to change without prior notice. Accordingly, compatibility may be impaired or some or all of the services may become unavailable. ■■Some functions of Pandora® cannot be operated from this unit. ■■For issues using the application, please contact Pandora® at pandora-support@ pandora.com English 15
  • Kenwood KDC-X696 | Instruction Manual - Page 16
    . Press the volume knob. 6 The receiver is connected to a Bluetooth device, with "HF CONNECT" or "AUD CONNECT" displayed, and exits the pairing mode. ■■If an error code is displayed during paring, see (page 30). When a Bluetooth device has already been registered, or maximum
  • Kenwood KDC-X696 | Instruction Manual - Page 17
    displayed. 6 Press to exit easy pairing mode. Registering from Bluetooth devices (Pairing) 1 Press SRC to turn on the power. 2 Start registering this unit by operating the Bluetooth device. By operating the Bluetooth device, register the hands-free unit or audio unit (pairing). Select "KENWOOD BT
  • Kenwood KDC-X696 | Instruction Manual - Page 18
    Phoning Preparation : You need to register your cell-phone before using it with this unit. (page 16) Built-in microphone (KDC-BT652U only) VOICE PAR iPod ■■Press to enter Bluetooth mode. ■■Press to answer an incoming call. ■■Press and hold to memorize the current phone number. ■■Press briefly to
  • Kenwood KDC-X696 | Instruction Manual - Page 19
    it again from the beginning. ■■Audio sound is not output during voice recognition. Receiving a Call Answering a Phone Call Press or the volume knob. ■■The following operations disconnect the line: Insert a CD. Connect a USB device. ■■The name of the calling party is displayed if it has already been
  • Kenwood KDC-X696 | Instruction Manual - Page 20
    when your cell-phone does not support the Phone Book Access Property (PBAP). 1 Press to enter Bluetooth mode. 2 Turn the volume knob to select [SETTINGS], then press to enter. 3 Turn the volume knob to select [TRANSFER PB], then press to enter. "DL PB ***" is displayed. 4 By operating the cell-phone
  • Kenwood KDC-X696 | Instruction Manual - Page 21
    ■■Bluetooth audio players that do not support AVRCP (Audio/Video Remote Control Profile) cannot be used with this unit. Operate from the audio player. ■■Some functions cannot be operated from the Bluetooth audio player. ■■Speakers from which audio is output change depending on the Bluetooth setting
  • Kenwood KDC-X696 | Instruction Manual - Page 22
    device, register the hands-free unit or audio unit (pairing). Select "KENWOOD BT CD/R-5T1" from the list of found units. 4 Input the PIN code ("0000") in the Bluetooth device. Check that registration is complete on the Bluetooth device. PIN code is set to "0000" as the default. You can change
  • Kenwood KDC-X696 | Instruction Manual - Page 23
    audio from the all speakers. CALL BEEP ON *: Sets whether to output a beep from the speaker when a call comes in. ; OFF: Cancels. BT F/W UPDATE Display the firmware version and update the firmware. MIC GAIN 1 - 8 *(KDC-BT652U) - 12 *(KDC-X696) - 15: Adjust the sensitivity of the microphone
  • Kenwood KDC-X696 | Instruction Manual - Page 24
    1 Press SRC to select a source other than "STANDBY". 2 Press the volume knob to enter [FUNCTION] mode. 3 Turn the volume knob to select [AUDIO CONTROL] or [SETTINGS], then press to enter. 4 Turn the volume knob to make a selection, then press to confirm. ■■See table below for selection. ■■Repeat
  • Kenwood KDC-X696 | Instruction Manual - Page 25
    STATUS You can display the connection status, signal strength, and battery level of Bluetooth device. HF-CON: Connection status for cell-phone. ; AD-CON: Connection status for BT Audio. ; BATT: Battery level of cell-phone. ; SIGNAL: Signal strength of cell-phone. TUNER SET TI: Selectable only
  • Kenwood KDC-X696 | Instruction Manual - Page 26
    Installation/connection Part list: A Faceplate 1) B Escutcheon 1) C Mounting sleeve 1) D Wiring harness 1) E Removal tool 2) F Flat head screw (for Nissan cars 4) G Round head screw (for Toyota cars 4) H Microphone (3 m) (KDC-X696 only)B 1) Basic procedure 1 Remove the key from the ignition
  • Kenwood KDC-X696 | Instruction Manual - Page 27
    Mounting and wiring this product requires skills and experience. For safety's sake, leave this work to professionals. If you experience problems during installation, consult your Kenwood dealer. ■■Reception may become poor if there are metal objects near the Bluetooth antenna. iPod Bluetooth antenna
  • Kenwood KDC-X696 | Instruction Manual - Page 28
    ) Antenna Cord Fuse (10A) Wiring harness D Rear output R L Front output Sub Woofer output Microphone H (KDC-X696 only) White White/Black Gray 12V) To connect the Kenwood navigation system, consult your navigation manual. Light Blue/Yellow (Steering remote control wire) Blue REMOTE CONT
  • Kenwood KDC-X696 | Instruction Manual - Page 29
    wiring harness to the C unit. Other wiring connection has been completed earlier. (page 28) D 2 1 3 Dashboard of C your car 4 5 B Bend the appropriate tabs to hold the mounting sleeve firmly in place. A Installing cars Removing the unit 1 Detach the faceplate A. 2 Engage the catch pin on
  • Kenwood KDC-X696 | Instruction Manual - Page 30
    Installing the Microphone Unit (KDC-X696 only) 1 Check the installation position of the microphone H. 2 Remove oil and other dirt from the H installation surface. 3 Install the microphone. 4 Wire the microphone cable up to the hands-free box with it secured at several positions using tape
  • Kenwood KDC-X696 | Instruction Manual - Page 31
    independently. Adjust it during handsfree talk. [MIC GAIN] of (page 22). No beep is heard at reception of an incoming No beep is heard depending on the type of your cell-phone. The [CALL BEEP] of call. (page 22) is set ON. Voice is not recognized. ■■The
  • Kenwood KDC-X696 | Instruction Manual - Page 32
    If this message still appears, press the reset button on the control unit. "HF ERROR 89" appears. Update of the Bluetooth firmware has failed. Retry it. "UNKNOWN" appears. The Bluetooth device cannot be detected. "DEVICE FULL" appears. 5 Bluetooth device have already been registered. No more
  • Kenwood KDC-X696 | Instruction Manual - Page 33
    Remote Control Profile) Audio section Maximum output power: 50 W × 4 Full bandwidth power (at less than 1 % THD): 22 W × 4 Speaker impedance: 4 Ω - 8 Ω Tone action: Bass: 100 Hz ±8 dB Middle: 1 kHz ±8 dB Treble: 12.5 kHz ±8 dB Preout level / load (CD): KDC-X696: 4,000 mV/ 10 kΩ KDC-BT652U: 2,500 mV
  • Kenwood KDC-X696 | Instruction Manual - Page 34
    accordance with the instructions. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to
  • Kenwood KDC-X696 | Instruction Manual - Page 35
    maximale autorisée. Cependant, cet équipement doit être installé et utilisé en gardant une distance de 20 cm relating to laser product safety. JVC KENWOOD Corporation 2967-3, ISHIKAWA-MACHI, HACHIOJI- type et d'un gain maximal (ou inférieur) approuvé pour l'émetteur par Industrie Canada. Dans le but
  • Kenwood KDC-X696 | Instruction Manual - Page 36
    KENWOOD
  • Kenwood KDC-X696 | Instruction Manual - Page 37
    INFORMATION/INFORMATIE/INFORMAZIONI/ INFORMACI0N/INFORMAc;0ES/ fi1HG>OPMA~fi1JI/IHG>OPMA~IJI/INFORMACJE/ INFORMACE/INFORMACIO/INFORMACIJA/ INFORMACIJE/INFORMATION/ ~Lo9 ' ' o/ 81161t About compatible iPod/iPhone Apropos des iPod/iPhone compatibles Ober kompatible iPod/iPhone Gerate Compatibele iPod
  • Kenwood KDC-X696 | Instruction Manual - Page 38
    product modification or failure to follow instructions contained in the Owner's Manual. "Accidental or intentional damages * Repairs or attempted repairs by an unauthorized agency. (All repairs must be performed at an authorized Kenwood Service Center.) • Damages or deteriorations caused during
  • Kenwood KDC-X696 | Instruction Manual - Page 39
    units are taken or sent for warranty service. you must include acopyollhe original daled sales receipl as proof of warranty coverage. LIMITATION follow instructions inthe owner's manual. (I) Oelects or damage as a resull ol repairs pertormed by a person or party nol aulhorized by KENWOOD (g)
  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
KDC-BT652U
KDC-X696
CD-RECEIVER
INSTRUCTION MANUAL
AMPLI-TUNER LECTEUR DE CD
MODE D’EMPLOI
REPRODUCTOR DE DISCOS COMPACTOS RECEPTOR DE FM/AM
MANUAL DE INSTRUCCIONES
B64-4919-00/02 (KW)
©
2011 JVC KENWOOD Corporation
Take the time to read through this instruction manual.
Familiarity with installation and operation procedures will help you obtain the best performance from
your new CD-receiver.
For your records
Record the serial number, found on the back of the unit, in the spaces designated on the warranty card, and in the
space provided
below. Refer to the model and serial numbers whenever you call upon your Kenwood dealer for
information or service on the product.
Model KDC-BT652U/ KDC-X696
Serial number
US Residents Only
Register Online
Register your Kenwood product at
www.Kenwoodusa.com