Kodak I1320 User Guide - Page 110

Replacing the pre-separation pad, Hold the separator module in both hands and find the two pre

Get Kodak I1320 - Document Scanner PDF manuals and user guides
UPC - 041771419783
View all Kodak I1320 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 110 highlights

4. Remove each tire by sliding the tire off the core. Replacing the preseparation pad 5. Install each new tire by gently pulling it over the core. 6. Replace the separation roller in the separation roller housing. Be sure the separation roller snaps into place. 7. Reinstall the separation module. 1. Remove the separation module from the scanner by following the steps described previously in "Replacing the separation module and tires" 2. Find the pre-separation pad on the separation module. 3. Hold the separator module in both hands and find the two preseparation pad side tabs which protrude slightly from the back of the separation module. 4. Push on the pre-separation pad side tabs on the back until the preseparation pad protrudes slightly from the front of the separation module. 106 A-61560 January 2007

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
106
A-61560 January 2007
4.
Remove each tire by sliding the tire off the core.
5.
Install each new tire by gently pulling it over the core.
6.
Replace the separation roller in the separation roller housing. Be
sure the separation roller snaps into place.
7.
Reinstall the separation module.
Replacing the pre-
separation pad
1.
Remove the separation module from the scanner by following the
steps described previously in “Replacing the separation module and
tires”
2.
Find the pre-separation pad on the separation module.
3.
Hold the separator module in both hands and find the two pre-
separation pad side tabs which protrude slightly from the back of the
separation module.
4.
Push on the pre-separation pad side tabs on the back until the pre-
separation pad protrudes slightly from the front of the separation
module.