Kodak I1860 User Guide - Page 23

Adjusting the height of the input elevator, Adjusting the input tray for document length - drivers

Get Kodak I1860 - Document Scanner PDF manuals and user guides View all Kodak I1860 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 23 highlights

Adjusting the height of the input elevator The input elevator can be set to accommodate stacks of 25-, 100-, 250or 500-documents of 20 lb. bond paper. Input elevator settings are made through the TWAIN Data source or ISIS Driver. NOTE: In this document 25 will be referred to as the highest setting and 500 as the lowest. Make this setting based on the number of documents you will place in the input elevator at one time. When set to 25 (Document Feeder or Normal), the input elevator will remain in position. When set to 100, 250 or 500, the input elevator will automatically raise to feed documents and lower after the last document in your stack has been fed. Adjusting the input tray for document length • No adjustments are required for documents up to 14 inches long. • If you are scanning documents from 14 to 17 inches in length, open the input elevator extension. • Documents longer than 17 inches require a document extender. Three sizes of document extenders are available for scanning documents from 43 cm (17 in.) to 86 cm (34 in.). See the section entitled, "Ordering parts" in Chapter 5 or contact your Kodak Field Engineer at 1-800-3KODAK3 (1-800-356-3253). 3-6 A-61555 April 2009

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
3-6
A-61555
April 2009
Adjusting the height of the
input elevator
The input elevator can be set to accommodate stacks of 25-, 100-, 250-
or 500-documents of 20 lb. bond paper. Input elevator settings are
made through the TWAIN Data source or ISIS Driver.
NOTE: In this document 25 will be referred to as the highest setting and
500 as the lowest.
Make this setting based on the number of documents you will place in
the input elevator at one time.
When set to 25 (Document Feeder or Normal), the input elevator will
remain in position. When set to 100, 250 or 500, the input elevator will
automatically raise to feed documents and lower after the last
document in your stack has been fed.
Adjusting the input tray for
document length
•
No adjustments are required for documents up to 14 inches long.
•
If you are scanning documents from 14 to 17 inches in length, open
the input elevator extension.
•
Documents longer than 17 inches require a document extender.
Three sizes of document extenders are available for scanning
documents from 43 cm (17 in.) to 86 cm (34 in.). See the section
entitled, “Ordering parts” in Chapter 5 or contact your Kodak Field
Engineer at 1-800-3KODAK3 (1-800-356-3253).