Konica Minolta AccurioPress 6136 AccurioPress 6136/6136P/610 User Guide Additi - Page 89

Finisher Adjustment, Large Capacity Stacker LS-507, Start, control panel

Get Konica Minolta AccurioPress 6136 PDF manuals and user guides View all Konica Minolta AccurioPress 6136 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 89 highlights

11 Finisher Adjustment 11.3 2 Press [Finisher Adjustment], [Stacker Adjustment], and [Standby Pos.(Rear Adj.)] in sequence. 3 When using two units of Large Capacity Stacker LS-507, select either [stacker 1] or [stacker 2]; when using three units of Large Capacity Stacker LS-507, select [stacker 1], [stacker 2], or [stacker 3]. 4 Press [Print Mode]. 5 Load the desired paper into a paper tray, and select that paper tray. 6 Press Start on the control panel. A test pattern is output, and printing is interrupted. A warning message is displayed on the screen. 7 Check whether the distance between the paper edge in Large Capacity Stacker LS-507 and the alignment plate position on the front is 5 mm in the crosswise direction. When the check is completed, remove paper. 8 If any adjustments are required, press [Exit PrintMode] to return to the [Standby Pos.(Rear Adj.)] screen. 9 Use the on-screen keypad to enter the numeric value. [Adj. Range: -20 ~ +20 1step = 0.1mm] [-] To narrow the standby position, [+] To widen the standby position % Use [+/-] to select the positive or negative value. % Press [Set], and change the current value to the setting value. 10 Repeat step 4 to step 9 until the desired result is obtained. 11-12 AccurioPress 6136/6136P/6120

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
11-12
AccurioPress 6136/6136P/6120
Finisher Adjustment
11
11.3
2
Press [Finisher Adjustment], [Stacker Adjustment], and [Standby Pos.(Rear Adj.)] in sequence.
3
When using two units of
Large Capacity Stacker LS-507
, select either [stacker 1] or [stacker 2]; when
using three units of
Large Capacity Stacker LS-507
, select [stacker 1], [stacker 2], or [stacker 3].
4
Press [Print Mode].
5
Load the desired paper into a paper tray, and select that paper tray.
6
Press
Start
on the
control panel
.
A test pattern is output, and printing is interrupted. A warning message is displayed on the screen.
7
Check whether the distance between the paper edge in
Large Capacity Stacker LS-507
and the
alignment plate position on the front is 5 mm in the crosswise direction.
When the check is completed, remove paper.
8
If any adjustments are required, press [Exit PrintMode] to return to the [Standby Pos.(Rear Adj.)] screen.
9
Use the on-screen keypad to enter the numeric value.
[Adj. Range: -20 ~ +20 1step = 0.1mm]
[-] To narrow the standby position, [+] To widen the standby position
%
Use [+/-] to select the positive or negative value.
%
Press [Set], and change the current value to the setting value.
10
Repeat step 4 to step 9 until the desired result is obtained.