LG 50144803 User Guide - Page 20

LG 50144803 - DLE5955W 27in Electric Dryer Manual

Get LG 50144803 - DLE5955W 27in Electric Dryer PDF manuals and user guides
UPC - 048231009157
View all LG 50144803 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 20 highlights

iNSTALLATIONINST UCTIONS DUCT CONDITION TESTING Your dryer features FIowSense an innovative sensor system that automatically detects blockages and restrictions in dryer ductwork. Keeping ductwork clean of lint build-up and free of restrictions allows clothes to dry faster, reduces energy use, and helps prevent fires. TM, Correct Venting When the dryer is first installed, the duct condition test must be performed. This alerts you to any existing problems before the dryer is used. The dryer also saves this information to compare and measure future changes. To activate the duct condition test cycle: O Press and hold the DAMP DRY BEEP and TEMP CONTROL buttons at the same time. While holding these buttons, press POWER ON/OFR f_ I :TcJ Restricted or Blocked Airflow Avoid long runs or runs with multiple elbows or bends. O The dryer will show InS in the number display to indicate that it is in duct condition testing mode. Press START/PAUSE. The dryer win run for approximately 2 minutes to test for blockages or restrictions to air flow in the ductwork. O If no bars are shown in the display, the ductwork is free from blockages or restrictions. Check for blockages and lint buildup. If all bars are Nt, the dryer ductwork has a blockage that needs to be removed immediately. Make sure the ductwork is not crushed or restricted. 0 % ..._J

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
iNSTALLATIONINST UCTIONS
DUCT CONDITION TESTING
Your dryer features
FIowSense
TM,
an
innovative
sensor system
that automatically
detects
blockages
and restrictions
in
dryer ductwork.
Keeping ductwork
clean of lint build-up
and free
of restrictions
allows
clothes
to dry faster, reduces
energy use, and helps prevent
fires.
When the dryer
is
first
installed,
the duct
condition
test must
be performed.
This alerts
you to any
existing
problems
before the dryer
is
used. The
dryer also saves this
information
to compare
and
measure
future changes.
To
activate
the
duct condition
test
cycle:
O
Press and
hold the DAMP DRY BEEP and
TEMP CONTROL
buttons
at the same time.
While holding
these
buttons,
press
POWER
ON/OFR
O
The dryer will show
InS
in
the number
display
to
indicate
that
it is in
duct
condition
testing
mode.
O
Press START/PAUSE.
The dryer win run for
approximately
2 minutes
to test
for blockages
or restrictions
to air
flow
in
the ductwork.
If no bars are shown
in
the display,
the ductwork
is
free from
blockages
or
restrictions.
If all bars are Nt, the dryer ductwork
has a blockage
that
needs to be
removed
immediately.
Correct
Venting
:TcJ
I
f_
Restricted
or
Blocked
Airflow
Avoid
long
runs or runs with
multiple
elbows
or bends.
Check for blockages
and lint buildup.
Make sure the ductwork
is
not crushed
or restricted.
0
%
.......................................................................................................................................................................................
_J