LG LDPS6762S Owners Manual - Page 50

Performance

Get LG LDPS6762S PDF manuals and user guides View all LG LDPS6762S manuals
Add to My Manuals
Save this manual to your list of manuals

Page 50 highlights

50 TROUBLESHOOTING Problem Noise Lights do not illuminate. Spray arms do not rotate smoothly. Upper rack is crooked. Dishwasher continuously chimes when the door is opened, during or right after a cycle has completed. Door does not close completely. (For models with cutlery rack) Dishwasher chimes if panel is touched during operation. Dishwasher did not finish cycle. Leaking in front of appliance Possible Cause & Solution Some level of noise is normal during operation. • Detergent cover opening. • Drain pump at the beginning of drain cycle. The dishwasher is not level. • Adjust leveling feet. Nozzle arm knocking against dishes. • Reposition the dishes. Power is not connected. • Connect power supply. Holes of spray arms are blocked by food particles. • Clean the holes of spray arms. Rack is poorly adjusted. • See the Height Adjustable Upper Rack section. This is a safety measure. Contact with escaping steam or the hot contents of the dishwasher could result in injury. • Close the door until the dishwasher and dishes have cooled down. The chiming will stop if the door is closed or the interior temperature has cooled. Cutlery rack is not properly loaded. • Push the door handle to close the door properly until it clicks. Bumping into or touching the control panel during operation may result in a disabled button sound. Only the Power, Start, Control Lock and Remote Start buttons are enabled during operation to prevent cycle settings from being changed inadvertently. • Button sounds can be turned off by using Option Setting Mode. Refer to the Using the Option Setting Mode topic. • The end of cycle chime and safety alert sounds will still sound. Door was opened during cycle. • If the door is opened during a cycle, the Start key must be pressed within 4 minutes or the machine turns off and all settings are lost. Dishwasher not leveled properly. • Verify the appliance is level from side to side and from front to back. See leveling instructions in the Installation section. Wrong detergent used. • If excessive sudsing is causing the leak, allow the foam to subside for 24 hours then clean the inside of the tub with milk. Performance Problem Odor Possible Cause & Solution The previous cycle was stopped before completion and residual water remains in the dishwasher. • Turn on the power, run the Cancel cycle option to remove the residual water, then run the Turbo cycle using detergent but with the dishwasher empty.

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
50
TROUBLESHOOTING
Performance
Noise
Some level of noise is normal during operation.
•
Detergent cover opening.
•
Drain pump at the beginning of drain cycle.
The dishwasher is not level.
•
Adjust leveling feet.
Nozzle arm knocking against dishes.
•
Reposition the dishes.
Lights do not
illuminate.
Power is not connected.
•
Connect power supply.
Spray arms do not
rotate smoothly.
Holes of spray arms are blocked by food particles.
•
Clean the holes of spray arms.
Upper rack is
crooked.
Rack is poorly adjusted.
•
See the
Height Adjustable Upper Rack
section.
Dishwasher
continuously chimes
when the door is
opened, during or
right after a cycle
has completed.
This is a safety measure. Contact with escaping steam or the hot contents of the
dishwasher could result in injury.
•
Close the door until the dishwasher and dishes have cooled down. The chiming will stop if
the door is closed or the interior temperature has cooled.
Door does not close
completely. (For
models with cutlery
rack)
Cutlery rack is not properly loaded.
•
Push the door handle to close the door properly until it clicks.
Dishwasher chimes if
panel is touched
during operation.
Bumping into or touching the control panel during operation may result in a disabled
button sound. Only the Power, Start, Control Lock and Remote Start buttons are
enabled during operation to prevent cycle settings from being changed inadvertently.
•
Button sounds can be turned off by using
Option Setting Mode
. Refer to the
Using the
Option Setting Mode
topic.
•
The end of cycle chime and safety alert sounds will still sound.
Dishwasher did not
finish cycle.
Door was opened during cycle.
•
If the door is opened during a cycle, the Start key must be pressed within 4 minutes or the
machine turns off and all settings are lost.
Leaking in front of
appliance
Dishwasher not leveled properly.
•
Verify the appliance is level from side to side and from front to back. See leveling
instructions in the Installation section.
Wrong detergent used.
•
If excessive sudsing is causing the leak, allow the foam to subside for 24 hours then clean
the inside of the tub with milk.
Problem
Possible Cause & Solution
Odor
The previous cycle was stopped before completion and residual water remains in the
dishwasher.
•
Turn on the power, run the
Cancel
cycle option to remove the residual water, then run the
Turbo
cycle using detergent but with the dishwasher empty.
Problem
Possible Cause & Solution