Lenovo PC 300GL User Guide (including system setup and option in - Page 105

See Updating System Programs on See IBM Enhanced Diagnostics

Get Lenovo PC 300GL PDF manuals and user guides View all Lenovo PC 300GL manuals
Add to My Manuals
Save this manual to your list of manuals

Page 105 highlights

POST Message 164 167 175 183 Description A change in the memory configuration occurred. This error can be caused by adding, removing, or incorrectly installing memory. Note: The computer can be used with decreased memory capacity until the error is corrected. Action: 1. If you added memory, see "Working with System Memory" on page 62 to verify that the new memory is correct for your computer and that it is installed correctly. 2. If you added or removed memory, you must save the new configuration before exiting from the Configuration/Setup Utility Program. 3. Running the diagnostic programs might isolate the location of the problem DIMM and provide additional information. See "IBM Enhanced Diagnostics" on page 116 for more information. If the problem cannot be corrected, have the computer serviced. A microprocessor was installed that is not supported by the current POST/BIOS (system programs). Action: 1. Obtain the latest POST/BIOS flash update diskette image. See "Updating System Programs" on page 22. 2. Perform the POST/BIOS flash update procedure. If the problem cannot be corrected, have the computer serviced. A failure occurred during testing of the system board and microprocessor. Action: Have the computer serviced. A password message is received if an administrator password is set. Action: You must enter the administrator password to clear this POST message. If the message recurs, have the computer serviced. Chapter 8. Troubleshooting 91

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
  • 171
  • 172
  • 173
  • 174
POST
Message
Description
164
A change in the memory configuration occurred.
This error can
be caused by adding, removing, or incorrectly installing memory.
Note:
The computer can be used with decreased memory
capacity until the error is corrected.
Action:
1.
If you added memory, see “Working with System Memory”
on page
62 to verify that the new memory is correct for your
computer and that it is installed correctly.
2.
If you added or removed memory, you must save the new
configuration before exiting from the Configuration/Setup
Utility Program.
3.
Running the diagnostic programs might isolate the location
of the problem DIMM and provide additional information.
See “IBM Enhanced Diagnostics” on page
116 for more
information.
If the problem cannot be corrected, have the computer serviced.
167
A microprocessor was installed that is not supported by the
current POST/BIOS (system programs).
Action:
1.
Obtain the latest POST/BIOS flash update diskette image.
See “Updating System Programs” on page
22.
2.
Perform the POST/BIOS flash update procedure.
If the problem cannot be corrected, have the computer serviced.
175
A failure occurred during testing of the system board and
microprocessor.
Action:
Have the computer serviced.
183
A password message is received if an administrator password is
set.
Action:
You must enter the administrator password to clear this
POST message.
If the message recurs, have the computer
serviced.
Chapter 8.
Troubleshooting
91