Lenovo S310 Lenovo S310 All-In-One Hardware Maintenance Manual - Page 103

Removing and reinstalling the system fan

Get Lenovo S310 PDF manuals and user guides View all Lenovo S310 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 103 highlights

5. Remove the screw that secures the system board shield, and then slide the system board shield out of the computer. Figure 24. Removing the system board shield 6. To reinstall the system board shield, slide the system board shield into the system board shield slot so that the screw hole aligns with that in the computer. 7. Reinstall the screw to secure the system board shield to the computer. 8. Go to "Completing the parts replacement" on page 121. Removing and reinstalling the system fan Attention Do not open your computer or attempt any repair before reading and understanding the "Important safety information" in the Safety, Warranty, and Setup Guide that came with your computer. To obtain a copy of the Safety, Warranty, and Setup Guide, go to: http://www.lenovo.com/support This section provides instructions on how to remove and reinstall the system fan. To remove and reinstall the system fan, do the following: 1. Remove all media from the drives and turn off all attached devices and the computer. Then, disconnect all power cords from electrical outlets and disconnect all cables that are connected to the computer. 2. Place a soft, clean towel or cloth on the desk or other flat surface. Hold the sides of your computer and gently lay it down so that the screen is against the surface and the cover is facing up. 3. Remove the computer cover. See "Removing the computer cover" on page 89. 4. Locate the system fan in the computer. See "FRU locations" on page 80. 5. Remove the system board shield. See "Removing and reinstalling the system board shield" on page 96. Chapter 8. Replacing FRUs 97

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
5. Remove the screw that secures the system board shield, and then slide the system board shield out
of the computer.
Figure 24. Removing the system board shield
6. To reinstall the system board shield, slide the system board shield into the system board shield slot so
that the screw hole aligns with that in the computer.
7. Reinstall the screw to secure the system board shield to the computer.
8. Go to “Completing the parts replacement” on page 121.
Removing and reinstalling the system fan
Attention
Do not open your computer or attempt any repair before reading and understanding the “Important safety
information” in the
Safety, Warranty, and Setup Guide
that came with your computer. To obtain a copy of the
Safety, Warranty, and Setup Guide
, go to:
This section provides instructions on how to remove and reinstall the system fan.
To remove and reinstall the system fan, do the following:
1. Remove all media from the drives and turn off all attached devices and the computer. Then, disconnect
all power cords from electrical outlets and disconnect all cables that are connected to the computer.
2. Place a soft, clean towel or cloth on the desk or other flat surface. Hold the sides of your computer and
gently lay it down so that the screen is against the surface and the cover is facing up.
3. Remove the computer cover. See “Removing the computer cover” on page 89.
4. Locate the system fan in the computer. See “FRU locations” on page 80.
5. Remove the system board shield. See “Removing and reinstalling the system board shield” on page 96.
Chapter 8
.
Replacing FRUs
97