Lenovo S310 Lenovo S310 All-In-One Hardware Maintenance Manual - Page 76

Voltage Sensors Voltage Regulator Module, Thermal Sensors Test Passed

Get Lenovo S310 PDF manuals and user guides View all Lenovo S310 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 76 highlights

Diagnostic Error Code FRU/Action 089-197-XXX Microprocessor test warning 1. Make sure the component that is called out is connected and/or enabled. See Chapter 6 "Using the Setup Utility program" on page 51. 2. Re-run test. 3. Replace the component that is called out in warning statement. 4. Replace the component under test. 089-198-XXX Microprocessor test aborted 1. Flash the system. See "Flash update procedures" on page 127. 2. Go to "Undetermined problems" on page 76. 089-199-XXX Microprocessor test failed, cause unknown 1. See "Undetermined problems" on page 76. 2. Flash the system and re-test. See "Flash update procedures" on page 127. 3. Replace component under function test. 170-000-XXX Voltage Sensor(s) Test Passed No action 170-0XX-XXX Voltage Sensor(s) failure 1. Flash system 2. System board 170-195-XXX Voltage Sensor(s) Test aborted by user Information only Restart the test, if necessary. 170-196-XXX Voltage Sensor(s) test halt, error threshold exceeded 1. Press F3 to review the log file. 2. Restart the test to reset the log file. 170-197-XXX Voltage Sensor(s) test warning 1. Make sure the component that is called out is connected and/or enabled. See Chapter 6 "Using the Setup Utility program" on page 51. 2. Re-run test. 3. Replace the component that is called out in warning statement. 4. Replace the component under test. 170-198-XXX Voltage Sensor(s) test aborted 1. If a component is called out, make sure it is connected and/or enabled. See Chapter 6 "Using the Setup Utility program" on page 51. 2. Flash the system and re-test. See "Flash update procedures" on page 127. 3. Go to "Undetermined problems" on page 76. 170-199-XXX Voltage Sensor(s) test failed, cause unknown 1. See "Undetermined problems" on page 76. 2. Flash the system and re-test. See "Flash update procedures" on page 127. 3. Replace component under function test. 170-250-XXX 170-251-XXX Voltage Sensor(s) Voltage limit error 1. Power supply 2. System board 170-254-XXX Voltage Sensor(s) Voltage Regulator Module error 1. Voltage Regulator Module (VRM) 2. Microprocessor 3. System board 175-000-XXX Thermal Sensor(s) Test Passed No action 175-0XX-XXX Thermal Sensor(s) failure 1. Flash system 2. System board 70 Lenovo S310 All-In-OneHardware Maintenance Manual

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
Diagnostic Error Code
FRU/Action
089-197-XXX
Microprocessor test warning
1. Make sure the component that is called out is
connected and/or enabled. See Chapter 6 “Using
the Setup Utility program” on page 51.
2. Re-run test.
3. Replace the component that is called out in warning
statement.
4. Replace the component under test.
089-198-XXX
Microprocessor test aborted
1. Flash the system. See “Flash update procedures”
on page 127.
2. Go to “Undetermined problems” on page 76.
089-199-XXX
Microprocessor test failed, cause unknown
1. See “Undetermined problems” on page 76.
2. Flash the system and re-test. See “Flash update
procedures” on page 127.
3. Replace component under function test.
170-000-XXX
Voltage Sensor(s) Test Passed
No action
170-0XX-XXX
Voltage Sensor(s) failure
1. Flash system
2. System board
170-195-XXX
Voltage Sensor(s) Test aborted by user
Information only Restart the test, if necessary.
170-196-XXX
Voltage Sensor(s) test halt, error threshold
exceeded
1. Press F3 to review the log file.
2. Restart the test to reset the log file.
170-197-XXX
Voltage Sensor(s) test warning
1. Make sure the component that is called out is
connected and/or enabled. See Chapter 6 “Using
the Setup Utility program” on page 51.
2. Re-run test.
3. Replace the component that is called out in warning
statement.
4. Replace the component under test.
170-198-XXX
Voltage Sensor(s) test aborted
1. If a component is called out, make sure it is
connected and/or enabled. See Chapter 6 “Using
the Setup Utility program” on page 51.
2. Flash the system and re-test. See “Flash update
procedures” on page 127.
3. Go to “Undetermined problems” on page 76.
170-199-XXX
Voltage Sensor(s) test failed, cause unknown
1. See “Undetermined problems” on page 76.
2. Flash the system and re-test. See “Flash update
procedures” on page 127.
3. Replace component under function test.
170-250-XXX 170-251-XXX
Voltage Sensor(s) Voltage
limit error
1. Power supply
2. System board
170-254-XXX
Voltage Sensor(s) Voltage Regulator Module
error
1. Voltage Regulator Module (VRM)
2. Microprocessor
3. System board
175-000-XXX
Thermal Sensor(s) Test Passed
No action
175-0XX-XXX
Thermal Sensor(s) failure
1. Flash system
2. System board
70
Lenovo S310 All-In-OneHardware Maintenance Manual