Home » Lenovo Manuals » Desktops » Lenovo ThinkCentre M90z » Manual Viewer

Lenovo ThinkCentre M90z Hardware Maintenance Manual for ThinkCentre M90z - Page 96

Replacing the multi-touch board, the system board and the multi-touch screen.

View all Lenovo ThinkCentre M90z manuals

Add to My Manuals
Save this manual to your list of manuals

Page 96 highlights

11. Go to "Completing the parts replacement" on page 110. Replacing the multi-touch board Attention Do not open your computer or attempt any repair before reading and understanding the "Important safety information" in the ThinkCentre Safety and Warranty Guide that came with your computer. To obtain a copy of the ThinkCentre Safety and Warranty Guide, go to:http://www.lenovo.com/support This section provides instructions on how to replace the multi-touch board. Note: The multi-touch board is available only in some models. To replace the multi-touch board, do the following: 1. Remove all media from the drives and turn off all attached devices and the computer. Then, disconnect all power cords from electrical outlets and disconnect all cables that are connected to the computer. 2. Place a soft, clean towel or cloth on the desk or surface. Hold the sides of your computer and gently lay it down so that the screen is against the surface and the cover is facing up. 3. Remove the computer cover. See "Removing the computer cover" on page 71. 4. Locate the multi-touch board in the computer. See "FRU locations" on page 69. 5. Note the multi-touch board cable routing and disconnect the three multi-touch board cables from the system board and the multi-touch screen. 6. Carefully remove the two screws 1 that secure the multi-touch board and then lift the multi-touch board off the computer main bracket. Figure 28. Removing the multi-touch board 7. Align the screw holes in the new multi-touch board with those in the computer main bracket and then install the two screws to secure the multi-touch board. 90 ThinkCentre Hardware Maintenance Manual

Section	Page
Chapter 1. About this manual	7
Important Safety Information	7
Chapter 2. Safety information	9
General safety	9
Electrical safety	9
Safety inspection guide	11
Handling electrostatic discharge-sensitive devices	11
Grounding requirements	12
Safety notices (multi-lingual translations)	12
Chapter 3. General information	35
Lenovo ThinkVantage Tools	35
SimpleTap	35
Lenovo Solution Center	35
ThinkVantage Productivity Center	35
Additional information resources	35
Specifications	36
Chapter 4. General Checkout	39
Problem determination tips	39
Chapter 5. Diagnostics	41
Lenovo ThinkVantage Toolbox	41
Lenovo Solution Center	41
PC-Doctor for Rescue and Recovery	42
PC-Doctor for DOS	42
Creating a diagnostic disc	42
Running the diagnostic program from the diagnostic disc	42
Navigating through the diagnostics programs	43
Running tests	43
Viewing the test log	44
Chapter 6. Using the Setup Utility program	45
Starting the Setup Utility program	45
Viewing or changing settings	45
Using passwords	45
Password considerations	46
Administrator password	46
Power-on password	46
Hard disk drive password	46
Setting, changing, or deleting a password	46
Enabling or disabling a device	47
Selecting a startup device	47
Selecting a temporary startup device	47
Viewing or changing the startup device sequence	47
Exiting the Setup Utility program	48
Chapter 7. Symptom-to-FRU Index	49
Hard disk drive boot error	49
Power Supply Problems	49
Diagnostic error codes	50
Beep symptoms	67
POST error codes	68
Miscellaneous error conditions	69
Undetermined problems	70
Chapter 8. Replacing FRUs	73
Locating controls and connectors on the front of your computer	73
Rear connectors	74
FRU locations	75
System board connectors	76
Removing the computer cover	77
Removing or reinstalling the frame stand	78
Removing or reinstalling the lift stand	78
Removing or reinstalling the rear I/O assembly cover	80
Removing or reinstalling the wall mount cover	81
Removing or reinstalling the wall mount	82
Installing or replacing a memory module	83
Replacing the battery	84
Replacing the hard disk drive	86
Replacing the optical drive	87
Replacing the heat sink	89
Replacing the microprocessor	91
Replacing the WI-FI card	94
Replacing the Bluetooth module	95
Replacing the multi-touch board	96
Replacing the ambient light sensor	97
Replacing the ExpressCard	98
Replacing the internal speakers	99
Replacing the integrated camera with microphone	100
Replacing the microprocessor fan assembly	101
Replacing the card reader	102
Replacing the rear I/O assembly	103
Replacing the right I/O assembly	105
Replacing the power supply	106
Replacing the inverter	107
Replacing the system fan	108
Replacing the power switch module	109
Replacing the touch panel control board	111
Replacing the system board	112
Replacing the LCD panel	115
Completing the parts replacement	116
Chapter 9. FRU lists	119
Overall: MT 0800, 0852, 0870, 2471, 3091, 3265, 3429, 3650, 5205, and 5248	119
Mechanical FRUs	137
Keyboard and Mouse	151
Adapters and miscellaneous FRUs	206
Power Cords	207
Recovery discs	219
Windows 7 Home Basic 32 Recovery CD	219
Windows 7 Home Basic 32 SP1 Recovery CD	222
Windows 7 Home Premium 32 Recovery CD	226
Windows 7 Home Premium 32 SP1 Recovery CD	231
Windows 7 Professional 32 Recovery CD	236
Windows 7 Professional 32 SP1 Recovery CD	245
Windows 7 Professional 64 Recovery CD	255
Windows 7 Professional 64 SP1 Recovery CD	260
Windows 7 Home Premium 64 Recovery CD	269
Windows 7 Home Premium 64 SP1 Recovery CD	269
Windows XP Professional 32 Recovery CD	270
Windows Vista Business 32 SP2 Recovery CD	271
Windows Vista Home Basic 32 SP2 Recovery CD	272
Windows 7 Ultimate 64 SP1 Recovery CD	274
Windows 7 Ultimate 32 SP1 Recovery CD	275
Windows Starter 32 SP1 Recovery CD	275
Chapter 10. Additional Service Information	279
Security features	279
Hardware controlled Passwords	279
Operating system password	279
Vital product data	279
BIOS levels	279
Flash update procedures	279
Updating (flashing) the BIOS from a disc	279
Updating (flashing) the BIOS from your operating system	280
Recovering from a POST/BIOS update failure	280
Power management	281
Automatic configuration and power interface (ACPI) BIOS	281
Automatic Power-On features	281
Appendix A. Notices	283
Television output notice	284
Trademarks	284

Match case Limit results 1 per page

11. Go to “Completing the parts replacement” on page 110.

Replacing the multi-touch board

Attention

Do not open your computer or attempt any repair before reading and understanding the “Important safety

information” in the

ThinkCentre Safety and Warranty Guide

that came with your computer. To obtain a copy

of the

ThinkCentre Safety and Warranty Guide

, go to:http://www.lenovo.com/support

This section provides instructions on how to replace the multi-touch board.

Note:

The multi-touch board is available only in some models.

To replace the multi-touch board, do the following:

1. Remove all media from the drives and turn off all attached devices and the computer. Then, disconnect

all power cords from electrical outlets and disconnect all cables that are connected to the computer.

2. Place a soft, clean towel or cloth on the desk or surface. Hold the sides of your computer and gently lay

it down so that the screen is against the surface and the cover is facing up.

3. Remove the computer cover. See “Removing the computer cover” on page 71.

4. Locate the multi-touch board in the computer. See “FRU locations” on page 69.

5. Note the multi-touch board cable routing and disconnect the three multi-touch board cables from

the system board and the multi-touch screen.

6. Carefully remove the two screws

that secure the multi-touch board and then lift the multi-touch

board off the computer main bracket.

Figure 28. Removing the multi-touch board

7. Align the screw holes in the new multi-touch board with those in the computer main bracket and then

install the two screws to secure the multi-touch board.

ThinkCentre Hardware Maintenance Manual