Lenovo ThinkStation E30 Hardware Maintenance Manual - Page 58

PCI Card Test Passed, PCI Card Failure

Get Lenovo ThinkStation E30 PDF manuals and user guides View all Lenovo ThinkStation E30 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 58 highlights

Diagnostic Error Code 015-196-XXX USB port test halt, error threshold exceeded 015-197-XXX USB port test warning 015-198-XXX USB port test aborted 015-199-XXX USB port test failed, cause unknown 018-000-XXX PCI Card Test Passed 018-0XX-XXX PCI Card Failure 018-195-XXX PCI Card Test aborted by user 018-196-XXX PCI Card test halt, error threshold exceeded 018-197-XXX PCI Card test warning 018-198-XXX PCI Card test aborted 018-199-XXX PCI Card test failed, cause unknown FRU/Action 1. Press F3 to review the log file. 2. Restart the test to reset the log file. 1. Make sure the component that is called out is connected and/or enabled. See Chapter 6 "Using the Setup Utility program" on page 37. 2. Re-run test. 3. Replace the component that is called out in warning statement. 4. Replace the component under test. 1. If a component is called out, make sure it is connected and/or enabled. See Chapter 6 "Using the Setup Utility program" on page 37. 2. Flash the system and re-test. See "Updating (flashing) the BIOS" on page 169. 3. Go to "Undetermined problems" on page 65. 1. Go to "Undetermined problems" on page 65. 2. Flash the system and re-test. See "Updating (flashing) the BIOS" on page 169. 3. Replace component under function test. No action 1. Riser card, if installed. 2. System board 1. PCI card 2. Information only Restart the test, if necessary 1. Press F3 to review the log file 2. Restart the test to reset the log file 1. Make sure the component that is called out is connected and/or enabled. See Chapter 6 "Using the Setup Utility program" on page 37. 2. Re-run test. 3. Replace the component that is called out in warning statement. 4. Replace the component under test. 1. If a component is called out, make sure it is connected and/or enabled. See Chapter 6 "Using the Setup Utility program" on page 37. 2. Flash the system and re-test. See "Updating (flashing) the BIOS" on page 169. 3. Go to "Undetermined problems" on page 65. 1. Go to "Undetermined problems" on page 65. 2. Flash the system and re-test. See "Updating (flashing) the BIOS" on page 169. 3. Replace component under function test. 52 ThinkStation Hardware Maintenance Manual

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
  • 171
  • 172
  • 173
  • 174
  • 175
  • 176
  • 177
  • 178
  • 179
  • 180
  • 181
  • 182
  • 183
  • 184
Diagnostic Error Code
FRU/Action
015-196-XXX
USB port test halt, error threshold exceeded
1. Press F3 to review the log file.
2. Restart the test to reset the log file.
015-197-XXX
USB port test warning
1. Make sure the component that is called out is
connected and/or enabled. See Chapter 6 “Using
the Setup Utility program” on page 37.
2. Re-run test.
3. Replace the component that is called out in warning
statement.
4. Replace the component under test.
015-198-XXX
USB port test aborted
1. If a component is called out, make sure it is
connected and/or enabled. See Chapter 6 “Using
the Setup Utility program” on page 37.
2. Flash the system and re-test. See “Updating
(flashing) the BIOS” on page 169.
3. Go to “Undetermined problems” on page 65.
015-199-XXX
USB port test failed, cause unknown
1. Go to “Undetermined problems” on page 65.
2. Flash the system and re-test. See “Updating
(flashing) the BIOS” on page 169.
3. Replace component under function test.
018-000-XXX
PCI Card Test Passed
No action
018-0XX-XXX
PCI Card Failure
1. Riser card, if installed.
2. System board
018-195-XXX
PCI Card Test aborted by user
1. PCI card
2. Information only Restart the test, if necessary
018-196-XXX
PCI Card test halt, error threshold exceeded
1. Press F3 to review the log file
2. Restart the test to reset the log file
018-197-XXX
PCI Card test warning
1. Make sure the component that is called out is
connected and/or enabled. See Chapter 6 “Using
the Setup Utility program” on page 37.
2. Re-run test.
3. Replace the component that is called out in warning
statement.
4. Replace the component under test.
018-198-XXX
PCI Card test aborted
1. If a component is called out, make sure it is
connected and/or enabled. See Chapter 6 “Using
the Setup Utility program” on page 37.
2. Flash the system and re-test. See “Updating
(flashing) the BIOS” on page 169.
3. Go to “Undetermined problems” on page 65.
018-199-XXX
PCI Card test failed, cause unknown
1. Go to “Undetermined problems” on page 65.
2. Flash the system and re-test. See “Updating
(flashing) the BIOS” on page 169.
3. Replace component under function test.
52
ThinkStation Hardware Maintenance Manual