LiftMaster 8365-267 8365-267 Owners Manual - Page 13

Install the Door Control, PRE-WIRED INSTALLATIONS

Get LiftMaster 8365-267 PDF manuals and user guides View all LiftMaster 8365-267 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 13 highlights

Install the Door Control 1 Install the Door Control To prevent possible SERIOUS INJURY or DEATH from electrocution: l Be sure power is NOT connected BEFORE installing door control. l Connect ONLY to 12 VOLT low voltage wires. To prevent possible SERIOUS INJURY or DEATH from a closing garage door: l Install door control within sight of garage door, out of reach of children at a minimum height of 5 feet (1.5 m), and away from ALL moving parts of door. l NEVER permit children to operate or play with door control push buttons or remote control transmitters. l Activate door ONLY when it can be seen clearly, is properly adjusted, and there are no obstructions to door travel. l ALWAYS keep garage door in sight until completely closed. NEVER permit anyone to cross path of closing garage door. INTRODUCTION Compatible with MyQ® and Security+ 2.0™ accessories, see page 32. Your garage door opener is compatible with up to 2 Smart Control Panels or 4 of any other Security+ 2.0™ door controls. NOTE: Older LiftMaster door controls and third party products are not compatible. Install the door control within sight of the door at a minimum height of 5 feet (1.5 m) where small children cannot reach, and away from the moving parts of the door. For gang box installations it is not necessary to drill holes or install the drywall anchors. Use the existing holes in the gang box. NOTE: Your product may look different than the illustrations. Screw 6-32x1" (2) Drywall Anchors (2) HARDWARE Screw 6ABx1" (2) 1. Strip 7/16 inch (11 mm) of insulation from one end of the wire and separate the wires. 2. Connect one wire to each of the two screws on the back of the door control. The wires can be connected to either screw. PRE-WIRED INSTALLATIONS: Choose any two wires to connect, note which wires are used so the correct wires are connected at the garage door opener in a later step. 3. Mark the location of the bottom mounting hole and drill a 5/32 inch (4 mm) hole. 4. Install the bottom screw, allowing 1/8 inch (3 mm) to protrude from the wall. 5. Position the bottom hole of the door control over the screw and slide down into place. 6. Lift the push bar up and mark the top hole. 7. Remove the door control from the wall and drill a 5/32 inch (4 mm) hole for the top screw. 8. Position the bottom hole of the door control over the screw and slide down into place. Attach the top screw. 1 2 7/16" (11 mm) 3 Wall 4-5 DRYWALL GANG BOX Drywall Anchor 6ABx1" 6-32x1" 7 8 6 DRYWALL Drywall Anchor 6ABx1" GANG BOX 6-32x1" 12

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
12
Install the Door Control
1 Install the Door Control
To prevent possible SERIOUS INJURY or DEATH from electrocution:
l
Be sure power is NOT connected BEFORE installing door control.
l
Connect ONLY to 12 VOLT low voltage wires.
To prevent possible SERIOUS INJURY or DEATH from a closing garage door:
l
Install door control within sight of garage door, out of reach of children at a minimum height
of 5 feet (1.5 m), and away from ALL moving parts of door.
l
NEVER permit children to operate or play with door control push buttons or remote control
transmitters.
l
Activate door ONLY when it can be seen clearly, is properly adjusted, and there are no
obstructions to door travel.
l
ALWAYS keep garage door in sight until completely closed. NEVER permit anyone to cross
path of closing garage door.
INTRODUCTION
Compatible with MyQ
®
and Security
+
2.0™ accessories, see page 32. Your garage door opener is
compatible with up to 2 Smart Control Panels or 4 of any other Security
+
2.0™ door controls.
NOTE:
Older LiftMaster door controls and third party products are not compatible.
Install the door control within sight of the door at a minimum height of 5 feet (1.5 m) where small children
cannot reach, and away from the moving parts of the door. For gang box installations it is not necessary
to drill holes or install the drywall anchors. Use the existing holes in the gang box.
NOTE:
Your product may look different than the illustrations.
HARDWARE
Screw
6ABx1" (2)
Drywall
Anchors (2)
Screw
6-32x1" (2)
1.
Strip 7/16 inch (11 mm) of insulation from one end of the wire and separate the wires.
2.
Connect one wire to each of the two screws on the back of the door control. The wires can be
connected to either screw.
PRE-WIRED INSTALLATIONS:
Choose any two wires to connect, note which wires are used
so the correct wires are connected at the garage door opener in a later step.
3.
Mark the location of the bottom mounting hole and drill a 5/32 inch (4 mm) hole.
4.
Install the bottom screw, allowing 1/8 inch (3 mm) to protrude from the wall.
5.
Position the bottom hole of the door control over the screw and slide down into place.
6.
Lift the push bar up and mark the top hole.
7.
Remove the door control from the wall and drill a 5/32 inch (4 mm) hole for the top screw.
8.
Position the bottom hole of the door control over the screw and slide down into place. Attach
the top screw.
7/16" (11 mm)
Wall
1
2
3
DRYWALL
GANG BOX
6ABx1"
6-32x1"
Drywall Anchor
4-5
6
6-32x1"
GANG BOX
8
DRYWALL
6ABx1"
Drywall Anchor
7