LiftMaster 8365-267 8365-267 Owners Manual - Page 28

Remote Control, To Add, Reprogram, Or Change A Remote Control/keyless Entry Pin Using

Get LiftMaster 8365-267 PDF manuals and user guides View all LiftMaster 8365-267 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 28 highlights

Operation Remote Control Your remote control has been programmed at the factory to operate with your garage door opener. Older LiftMaster remote controls are NOT compatible, see page 32 for compatible accessories. Programming can be done through the door control or the learn button the garage door opener. To program additional accessories refer to the instructions provided with the accessory or visit www.liftmaster.com . If your vehicle is equipped with a Homelink®, you may require an external adapter depending on the make, model, and year of your vehicle. Visit www.homelink.com for additional information. TO ADD, REPROGRAM, OR CHANGE A REMOTE CONTROL/KEYLESS ENTRY PIN USING THE DOOR CONTROL 1. Press the LEARN button on the door control to enter Programming Mode. 2. Press the LEARN button again, the LED will flash once. 3. Remote Control: Press the button on the remote control that you wish to operate your garage door. Keyless Entry: Enter a 4-digit personal identification number (PIN) of your choice on the keyless entry keypad. Then press the ENTER button. The garage door opener lights will flash (or two clicks will be heard) when the code has been programmed. Repeat the steps above for programming additional remote controls or keyless entry devices. If programming is unsuccessful, program the remote using the learn button. 1 The command LED will flash once. 2 The command LED will flash once again. PROGRAM USING THE GARAGE DOOR OPENER 1. 2. 3. 1-2 Locate the Learn button on the garage door opener. Press and immediately release the Learn button. The Learn LED will glow steady for 30 seconds. Within 30 seconds... Press and hold the button the remote control that you wish to use. Release the button when the garage door opener lights blink or two clicks are heard. If programming to other products, press the button a second time to activate products. 3 "cli"cckl"ick" LEARN Button LEARN LED To Erase the Memory ERASE ALL REMOTE CONTROLS AND KEYLESS ENTRIES 1. Press and hold the learn button on garage door opener until the learn LED goes out (approximately 6 seconds). All remote control and keyless entry codes are now erased. Reprogram any accessory you wish to use. ERASE ALL DEVICES (Including MyQ® enabled accessories) 1. Press and hold the learn button on garage door opener until the learn LED goes out (approximately 6 seconds). 2. Immediately press and hold the learn button again until the learn LED goes out. All codes are now erased. Reprogram any accessory you wish to use. 3 OR 4GHI 5JKL 6 MNO 7PRS 8TUV 9WXY * * 0 QZ # 0 QZ # ENTER ENTER ???? PIN 27

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
27
Operation
Remote Control
Your remote control has been programmed at the factory to operate with your garage door opener.
Older LiftMaster remote controls are NOT compatible, see page 32 for compatible accessories.
Programming can be done through the door control or the learn button the garage door opener. To
program additional accessories refer to the instructions provided with the accessory or visit
www.liftmaster.com . If your vehicle is equipped with a Homelink
®
, you may require an external adapter
depending on the make, model, and year of your vehicle. Visit www.homelink.com for additional
information.
TO ADD, REPROGRAM, OR CHANGE A REMOTE CONTROL/KEYLESS ENTRY PIN USING THE
DOOR CONTROL
1.
Press the LEARN button on the door control to enter Programming Mode.
2.
Press the LEARN button again, the LED will flash once.
3.
Remote Control:
Press the button on the remote control that you wish to operate your garage door.
Keyless Entry:
Enter a 4-digit personal identification number (PIN) of your choice on the keyless entry
keypad. Then press the ENTER button.
The garage door opener lights will flash (or two clicks will be heard) when the code has been
programmed. Repeat the steps above for programming additional remote controls or keyless entry
devices. If programming is unsuccessful, program the remote using the learn button.
The command LED
will flash once.
The command LED will
flash once again.
1
2
OR
PIN
?
?
?
?
4
5
7
8
9
0
*
#
ENTER
0
QZ
*
#
ENTER
6
3
PROGRAM USING THE GARAGE DOOR OPENER
1.
Locate the Learn button on the garage door opener.
2.
Press and immediately release the Learn button. The Learn LED will glow steady for 30
seconds. Within 30 seconds...
3.
Press and hold the button the remote control that you wish to use. Release the button when
the garage door opener lights blink or two clicks are heard. If programming to other products,
press the button a second time to activate products.
LEARN LED
LEARN
Button
“click”
“click”
1-2
3
To Erase the Memory
ERASE ALL REMOTE CONTROLS AND KEYLESS ENTRIES
1.
Press and hold the learn button on garage door opener until the learn LED goes out
(approximately 6 seconds). All remote control and keyless entry codes are now erased.
Reprogram any accessory you wish to use.
ERASE ALL DEVICES (Including MyQ
®
enabled accessories)
1.
Press and hold the learn button on garage door opener until the learn LED goes out
(approximately 6 seconds).
2.
Immediately press and hold the learn button again until the learn LED goes out. All codes are
now erased.
Reprogram any accessory you wish to use.