LiftMaster 8365-267 8365-267 Owners Manual - Page 22

Program the Travel, PROGRAMMING BUTTONS, UP Button, Adjustment Button, DOWN Button

Get LiftMaster 8365-267 PDF manuals and user guides View all LiftMaster 8365-267 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 22 highlights

Adjustments 1 Program the Travel Without a properly installed safety reversal system, persons (particularly small children) could be SERIOUSLY INJURED or KILLED by a closing garage door. l Incorrect adjustment of garage door travel limits will interfere with proper operation of safety reversal system. l After ANY adjustments are made, the safety reversal system MUST be tested. Door MUST reverse on contact with 1-1/2" (3.8 cm) high object (or 2x4 laid flat) on floor. While programming, the UP and DOWN buttons can be used to move the door as needed. 1. Press and hold the Adjustment Button until the UP Button begins to flash and/or a beep is 1 heard. 2. Press and hold the UP Button until the door is in the desired UP position. 3. Once the door is in the desired UP position press and release the Adjustment Button. The garage door opener lights will flash twice and the DOWN Button will begin to flash. 4. Press and hold the DOWN Button until the door is in the desired DOWN position. 5. Once the door is in the desired DOWN position press and release the Adjustment Button. The garage door opener lights will flash twice and the UP Button will begin to flash. 4 6. Press and release the UP Button. When the door travels to the programmed UP position, the DOWN Button will begin to flash. 7. Press and release the DOWN Button. The door will travel to the programmed DOWN position. Programming is complete. If the garage door opener lights are flashing 5 times during the steps for Program the Travel, the programming has timed out. If the garage door opener lights are flashing 10 times during the steps for Program the Travel, the safety reversing sensors are misaligned or obstructed (refer to page 19). When the sensors are aligned and unobstructed, cycle the door through a complete up and down cycle using 6 the remote control or the UP and DOWN buttons. Programming is complete. If you are unable to operate the door up and down, repeat the steps for Programming the Travel. 21 PROGRAMMING BUTTONS UP Button Adjustment Button DOWN Button 2 3 5 7

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
21
Adjustments
1 Program the Travel
Without a properly installed safety reversal system, persons (particularly small children) could be
SERIOUSLY INJURED or KILLED by a closing garage door.
l
Incorrect adjustment of garage door travel limits will interfere with proper operation of
safety reversal system.
l
After ANY adjustments are made, the safety reversal system MUST be tested. Door MUST
reverse on contact with 1-1/2" (3.8 cm) high object (or 2x4 laid flat) on floor.
While programming, the UP and DOWN buttons can be used to move the door as needed.
1.
Press and hold the Adjustment Button until the UP Button begins to flash and/or a beep is
heard.
2.
Press and hold the UP Button until the door is in the desired UP position.
3.
Once the door is in the desired UP position press and release the Adjustment Button. The
garage door opener lights will flash twice and the DOWN Button will begin to flash.
4.
Press and hold the DOWN Button until the door is in the desired DOWN position.
5.
Once the door is in the desired DOWN position press and release the Adjustment Button. The
garage door opener lights will flash twice and the UP Button will begin to flash.
6.
Press and release the UP Button. When the door travels to the programmed UP position, the
DOWN Button will begin to flash.
7.
Press and release the DOWN Button. The door will travel to the programmed DOWN position.
Programming is complete.
If the garage door opener lights are flashing 5 times during the steps for Program the Travel, the
programming has timed out. If the garage door opener lights are flashing 10 times during the steps for
Program the Travel, the safety reversing sensors are misaligned or obstructed (refer to page 19). When
the sensors are aligned and unobstructed, cycle the door through a complete up and down cycle using
the remote control or the UP and DOWN buttons. Programming is complete. If you are unable to operate
the door up and down, repeat the steps for Programming the Travel.
PROGRAMMING BUTTONS
UP Button
Adjustment Button
DOWN Button
1
2
3
4
5
6
7