LiftMaster 8365-267 8365-267 Owners Manual - Page 2

Preparation, Safety Symbol and Signal Word, Review, Check the Door, Tools Needed

Get LiftMaster 8365-267 PDF manuals and user guides View all LiftMaster 8365-267 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 2 highlights

Preparation Check the Door Safety Symbol and Signal Word Review This garage door opener has been designed and tested to offer safe service provided it is installed, operated, maintained and tested in strict accordance with the instructions and warnings contained in this manual. When you see these Safety Symbols and Signal Words on the following pages, they will alert you to the possibility of serious injury or death if you do not comply with the warnings that accompany them. The hazard may come from something mechanical or from electric shock. Read the warnings carefully. Mechanical Electrical When you see this Signal Word on the following pages, it will alert you to the possibility of damage to your garage door and/or the garage door opener if you do not comply with the cautionary statements that accompany it. Read them carefully. To prevent possible SERIOUS INJURY or DEATH: l ALWAYS call a trained door systems technician if garage door binds, sticks, or is out of balance. An unbalanced garage door may NOT reverse when required. l NEVER try to loosen, move or adjust garage door, door springs, cables, pulleys, brackets or their hardware, ALL of which are under EXTREME tension. l Disable ALL locks and remove ALL ropes connected to garage door BEFORE installation and operating garage door opener to avoid entanglement. To prevent damage to garage door and opener: l ALWAYS disable locks BEFORE installing and operating the opener. l ONLY operate garage door opener at 120V, 60 Hz to avoid malfunction and damage. 1. Disable locks and remove any ropes Tools Needed connected to the garage door. 2. Lift the door halfway up. Release the door. If balanced, it should stay in place, supported entirely by its springs. 3. Raise and lower the door to check for binding or sticking. If your door binds, sticks, or is out of balance, call a trained door systems technician. 4. Check the seal on the bottom of the door. Any gap between the floor and the bottom of the door must not exceed 1/4 inch (6 mm). Otherwise, the safety reversal system may not work properly. 5. The opener should be installed above the center of the door. If there is a torsion spring or center bearing plate in the way of the header bracket, it may be installed 5/32 3/16 5/16 within 4 feet (1.2 m) to the left or right of 12 the door center. See page 5. Torsion Spring OR Extension Spring 1/2 5/8 1/4 7/16 9/16 7/16 1

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
1
Safety Symbol and Signal Word
Review
This garage door opener has been designed and
tested to offer safe service provided it is installed,
operated, maintained and tested in strict
accordance with the instructions and warnings
contained in this manual.
When you see these Safety Symbols and Signal
Words on the following pages, they will alert you to
the possibility of
serious injury or death
if you do
not comply with the warnings that accompany them.
The hazard may come from something mechanical
or from electric shock. Read the warnings carefully.
Mechanical
Electrical
When you see this Signal Word on the following
pages, it will alert you to the possibility of damage to
your garage door and/or the garage door opener if
you do not comply with the cautionary statements
that accompany it. Read them carefully.
Check the Door
To prevent possible SERIOUS INJURY or
DEATH:
l
ALWAYS call a trained door systems
technician if garage door binds, sticks,
or is out of balance. An unbalanced
garage door may NOT reverse when
required.
l
NEVER try to loosen, move or adjust
garage door, door springs, cables,
pulleys, brackets or their hardware,
ALL of which are under EXTREME
tension.
l
Disable ALL locks and remove
ALL ropesconnected to garage door
BEFORE installation and operating
garage door opener to avoid
entanglement.
To preventdamage to garage door and opener:
l
ALWAYS disable locks BEFORE
installing and operating the opener.
l
ONLY operate garage door opener at
120V, 60 Hz to avoid malfunction and
damage.
1.
Disable locks and remove any ropes
connected to the garage door.
2.
Lift the door halfway up. Release the
door. If balanced, it should stay in place,
supported entirely by its springs.
3.
Raise and lower the door to check for
binding or sticking. If your door binds,
sticks, or is out of balance, call a trained
door systems technician.
4.
Check the seal on the bottom of the door.
Any gap between the floor and the
bottom of the door must not exceed
1/4 inch (6 mm). Otherwise, the safety
reversal system may not work properly.
5.
The opener should be installed above
the center of the door. If there is a torsion
spring or center bearing plate in the way
of the header bracket, it may be installed
within 4 feet (1.2 m) to the left or right of
the door center.See page 5.
Torsion
Spring
Extension
Spring
OR
Tools Needed
2
1
3/16
7/16
1/2
5/32
5/16
5/8
9/16
1/4
7/16
Preparation