LiftMaster ATS ATS2113X Manual - Page 30

To Add or Change a Keyless Entry PIN Optional

Get LiftMaster ATS PDF manuals and user guides View all LiftMaster ATS manuals
Add to My Manuals
Save this manual to your list of manuals

Page 30 highlights

To Add or Change a Keyless Entry PIN (Optional) NOTE: Your new Keyless Entry must be programmed to operate your garage door opener. USING THE "LEARN" BUTTON 1. Press and release the "learn" button on motor unit. The learn indicator light will glow steadily for 30 seconds. 2. Within 30 seconds, enter a four digit personal identification number (PIN) of your choice on the keypad. Then press and hold the enter button. 3. Release the button when the motor unit lights blink. It has learned the code. If light bulbs are not installed, two clicks will be heard. To change an existing, known PIN If the existing PIN is known, it may be changed by one person without using a ladder. 1. Press the four buttons for the present PIN, then press and hold the # button. The opener light will blink twice. Release the # button. 2. Press the new 4-digit PIN you have chosen, then press ENTER. The motor unit lights will blink once when the PIN has been learned. Test by pressing the new PIN, then press ENTER. The door should move. To set a temporary PIN You may authorize access by visitors or service people with a temporary 4-digit PIN. After a programmed number of hours or number of accesses, this temporary PIN expires and will no longer open the door. It can be used to close the door even after it has expired. To set a temporary PIN: 1. Press the four buttons for your personal entry PIN (not the last temporary PIN), then press and hold the ✽ button. The opener light will blink three times. Release the button. 2. Press the temporary 4-digit PIN you have chosen, then press ENTER. The opener light will blink four times. 3. To set the number of hours this temporary PIN will work, press the number of hours (up to 255), then press ✽. OR 3. To set the number of times this temporary PIN will work, press the number of times (up to 255), then press #. The opener light will blink once when the temporary PIN has been learned. Test by pressing the four buttons for the temporary PIN, then press ENTER. The door should move. If the temporary PIN was set to a certain number of openings, remember that the test has used up one opening. To clear the temporary password, repeat steps 1-3, setting the number of hours or times to 0 in step 3. 30

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
30
1.
Press and release the “learn”
button on motor unit. The
learn indicator light will glow
steadily for 30 seconds.
2.
Within 30 seconds, enter a four
digit personal identification
number (PIN) of your choice
on the keypad. Then press and
hold the enter button.
3.
Release the button when the
motor unit lights blink. It has
learned the code. If light bulbs
are not installed, two clicks will
be heard.
To Add or Change a Keyless Entry PIN (Optional)
NOTE:
Your new Keyless Entry must be programmed to operate your garage door opener.
USING THE “LEARN” BUTTON
To change an existing, known PIN
If the existing PIN is known, it may be changed by one
person without using a ladder.
1.
Press the four buttons for the present PIN, then press
and hold the # button.
The opener light will blink twice. Release the # button.
2.
Press the new 4-digit PIN you have chosen, then press
ENTER.
The motor unit lights will blink once when the PIN has
been learned.
Test by pressing the new PIN, then press ENTER. The
door should move.
To set a temporary PIN
You may authorize access by visitors or service people
with a temporary 4-digit PIN. After a programmed
number of hours or number of accesses, this temporary
PIN expires and will no longer open the door. It can be
used to
close
the door even after it has expired. To set a
temporary PIN:
1.
Press the four buttons for your personal entry PIN
(not the last temporary PIN), then press and hold the
✽
button.
The opener light will blink three times. Release the
button.
2.
Press the temporary 4-digit PIN you have chosen, then
press ENTER.
The opener light will blink four times.
3.
To set the number of
hours
this temporary PIN will
work, press the number of hours (up to 255), then
press
✽
.
OR
3.
To set the number of
times
this temporary PIN will
work, press the number of times (up to 255), then
press #.
The opener light will blink once when the temporary PIN
has been learned.
Test by pressing the four buttons for the temporary
PIN, then press ENTER. The door should move. If the
temporary PIN was set to a certain number of openings,
remember that the test has used up one opening. To clear
the temporary password, repeat steps 1-3, setting the
number of hours or times to 0 in step 3.