LiftMaster MEGA SLIDE-X MEGA SLIDE-X MSLXDCBB Manual - Page 7

Safety Precautions For Open Roller Gates, Warning Sign Placement, Do Not Mount Accessories That Are

Page 7 highlights

SAFETY PRECAUTIONS FOR OPEN ROLLER GATES WARNING • Injuries occur when people get their hands or feet caught CAUTION between the top or bottom of the gate and the gate roller. These potential pinch-points should be guarded against at ALL times. Enclosed style gate tracks are available for refitting of these rollers from many fence suppliers. Also, roller guards are available for installing over the rollers. • UL325 requires that, when used, contact sensors shall be located at the leading edge, trailing edge, and be post mounted both inside and outside of a vehicular horizontal slide gate. Non-contact sensors such as photo eyes must protect during both open and close gate cycles. • Injuries occur when people put their hands and arms through openings in the grill while the gate is operating. They cannot retract their arm and it gets caught between the moving gate grill and the stationary fence post or fence. This AVERTISSEMENT potential hazard can be averted by placing a 4' (1.2 m) screen mesh on the gate to prevent access through openings anywhere the gate may travel. See Safety Brochure for details. To prevent entrapment injuries, mount controls ATTENTION at least 6' (1.8 m) from the gate or ANY moving parts of the gate. Gate Edge on Rear of Gate for Open Direction Gate Edge on Fence Post for Open Direction Gate Edge on WARNING Leading Edge of Gate for Close Direction Photo Beam for Open Direction Pinch-Point Hazard UNIT Additional Post Mounted Gate Edge for Close Direction WARNING Photo Beam for Close Direction Additional Post Mounted Gate Edge for Open Direction Always Test Gate Edges and Photo Beams Anytime They Are Adjusted or Serviced Gate Edge Pinch-Point Hazard AVERTISSGEate EMdge Efor NT Gate Edge for Close Direction Open Direction AVERTISSEMENT Vertical Post Placed on Both Sides of the Exposed Rollers Can Prevent Hands From Reaching These Pinch-Points Gate Edge for Close Direction DO NOT MOUNT ACCESSORIES THAT ARE ACCESSIBLE THROUGH GATE! WARNING SIGNAPDLAVCEEMERNTTENCIA PREWCAARUNCIINÓGN To prevent SERIOUS INJURY or DEATH from a moving gate: CAUTION • Install Warning signs on EACH side of gate in PLAIN VIEW. • Permanently secure each Warning sign in a suitable manner using fastening holes. NOT FOR USE AS PEDESTRIAN PASSAGE! This operator is intended for vehicular use only. To prevent INJURY to pedestrians, a separate pedestrian access should be supplied, visible from the gate. Locate the pedestrian access where there is not a chance of INJURY at any point during full movement of the gate. AVERTISSEMENT 7 ADVERTENCIA AWDVAERRNTINEGNCIA WARNING Moving Gate Can Cause Injury or Death KEEP CLEAR! Gate may move at any time without prior warning. Do not let children operate the gate or play in the gate area. This entrance is for vehicles onl.y Pedestrians must use separate entrance AVERTISSEMENT

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24

7
NOT FOR USE AS PEDESTRIAN PASSAGE! This operator is
intended for vehicular use only. To prevent INJURY to
pedestrians, a separate pedestrian access should be supplied,
visible from the gate. Locate the pedestrian access where there is
not a chance of INJURY at any point during full movement of the
gate.
DO NOT MOUNT ACCESSORIES THAT ARE
ACCESSIBLE THROUGH GATE!
WARNING SIGN PLACEMENT
Moving Gate Can Cause
Injury or Death
KEEP CLEAR!
Gate may move at any
time without prior warning.
Do not let children operate the gate or
play in the gate area.
This entrance is for vehicles only
.
Pedestrians must use separate entrance
SAFETY PRECAUTIONS FOR OPEN ROLLER GATES
To prevent SERIOUS INJURY or DEATH from a moving gate:
Install Warning signs on EACH side of gate in PLAIN
VIEW.
• Permanently secure each Warning sign in a suitable
manner using fastening holes.
• Injuries occur when people get their hands or feet caught
between the top or bottom of the gate and the gate roller.
These potential pinch-points should be guarded against at
ALL times. Enclosed style gate tracks are available for
refitting of these rollers from many fence suppliers. Also,
roller guards are available for installing over the rollers.
• UL325 requires that, when used, contact sensors shall be
located at the leading edge, trailing edge, and be post
mounted both inside and outside of a vehicular horizontal
slide gate. Non-contact sensors such as photo eyes must
protect during both open and close gate cycles.
• Injuries occur when people put their hands and arms
through openings in the grill while the gate is operating.
They cannot retract their arm and it gets caught between the
moving gate grill and the stationary fence post or fence. This
potential hazard can be averted by placing a 4' (1.2 m)
screen mesh on the gate to prevent access through
openings anywhere the gate may travel. See Safety Brochure
for details. To prevent entrapment injuries, mount controls
at least 6' (1.8 m) from the gate or ANY moving parts of the
gate.
Gate Edge on Rear
of Gate for Open
Direction
Gate Edge on Fence Post
for Open Direction
Gate Edge on
Leading Edge of Gate for
Close Direction
Photo Beam
for Open
Direction
Photo Beam for
Close Direction
UNIT
Additional Post Mounted Gate
Edge for Close Direction
Additional Post Mounted Gate
Edge for Open Direction
Pinch-Point
Hazard
Pinch-Point
Hazard
Gate Edge for
Close Direction
Gate Edge for
Close Direction
Gate Edge for
Open Direction
Always Test Gate Edges and Photo
Beams Anytime They Are Adjusted or
Serviced
Gate Edge
Vertical Post Placed on Both
Sides of the Exposed Rollers
Can Prevent Hands From
Reaching These Pinch-Points
WARNING
WARNING
WARNING
WARNING