Lowrance HDS-7 LIVE HDS Live Installation Manual - Page 51

Receive waypoint, Serial ports, Serial Output, Serial output sentences, Ethernet/Wireless

Get Lowrance HDS-7 LIVE PDF manuals and user guides View all Lowrance HDS-7 LIVE manuals
Add to My Manuals
Save this manual to your list of manuals

Page 51 highlights

Receive waypoint Select this option to allow a device capable of creating and exporting waypoints via NMEA 0183 to transfer directly to this unit. Serial ports Specifies the baud rate and protocol for the NMEA 0183 interface. The baud rate should be set to correspond with devices connected to the NMEA 0183 input and output. Serial Output Selection determines whether the data is output via Tx lines, and will enable editing of the output sentences list. Serial output sentences This list allows control over which sentences need to be transmitted to other devices from the NMEA 0183 port. Due to the limited bandwidth of NMEA 0183 it is desirable to only enable the data that is required. The less sentences that are selected, the higher the output rate of the enabled sentences. Commonly used sentences are enabled by default. Ethernet/Wireless The NMEA 0183 data stream is output and made available to tablet devices and PCs, via the internal wireless or Ethernet. The dialogue provides IP and port data typically required for configuring the application on the third party device. Ú Note: Other MFDs cannot decode this information back to NMEA 0183, to use the data as a source. To share data a physical NMEA 2000 or NMEA 0183 connection is still required. Software setup | HDS Live Installation Manual 51

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
Receive waypoint
Select this option to allow a device capable of creating and
exporting waypoints via NMEA 0183 to transfer directly to this unit.
Serial ports
Specifies the baud rate and protocol for the NMEA 0183 interface.
The baud rate should be set to correspond with devices connected
to the NMEA 0183 input and output.
Serial Output
Selection determines whether the data is output via Tx lines, and
will enable editing of the output sentences list.
Serial output sentences
This list allows control over which sentences need to be transmitted
to other devices from the NMEA 0183 port. Due to the limited
bandwidth of NMEA 0183 it is desirable to only enable the data that
is required. The less sentences that are selected, the higher the
output rate of the enabled sentences.
Commonly used sentences are enabled by default.
Ethernet/Wireless
The NMEA 0183 data stream is output and made available to tablet
devices and PCs, via the internal wireless or Ethernet. The dialogue
provides IP and port data typically required for configuring the
application on the third party device.
Ú
Note:
Other MFDs cannot decode this information back to
NMEA 0183, to use the data as a source. To share data a physical
NMEA 2000 or NMEA 0183 connection is still required.
Software setup
| HDS Live Installation Manual
51