Makita LS1219L LS1219L Instruction Manual - Page 26

Table C

Get Makita LS1219L PDF manuals and user guides View all Makita LS1219L manuals
Add to My Manuals
Save this manual to your list of manuals

Page 26 highlights

Crown molding stopper Optional accessory Crown molding stoppers allow easier cuts of crown molding without tilting the saw blade. Install them on the turn base as shown in the figures. 1 At right 45° miter angle 1 2 3 4 2 ► 1 . Guide fence 2. Crown molding stopper ► 1 . Crown molding stopper L 2. Crown molding stopper R 3. Turn base 4. Guide fence At left 45° miter angle 1 (a) (b) 1 (c) (d) 2 2 3 4 ► 1 . Crown molding stopper L 2. Crown molding stopper R 3. Turn base 4. Guide fence Position crown molding with its WALL CONTACT EDGE against the guide fence and its CEILING CONTACT EDGE against the crown molding stoppers as shown in the figure. Adjust the crown molding stoppers according to the size of the crown molding. Tighten the screws to secure the crown molding stoppers. Refer to the table (C) for the miter angle. 1. Inside corner 2. Outside corner Table (C) - For inside corner For outside corner Molding position in the figure (a) (b) (c) (d) Miter angle Finished piece Right 45° Left 45° Right 45° Save the right side of blade Save the left side of blade Save the right side of blade Save the left side of blade 26 ENGLISH

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
26
ENGLISH
Crown molding stopper
Optional accessory
Crown molding stoppers allow easier cuts of crown
molding without tilting the saw blade. Install them on the
turn base as shown in the figures.
At right 45° miter angle
1
2
3
4
►
1.
Crown molding stopper L
2.
Crown molding stop-
per R
3.
Turn base
4.
Guide fence
At left 45° miter angle
1
4
2
3
►
1.
Crown molding stopper L
2.
Crown molding stop-
per R
3.
Turn base
4.
Guide fence
Position crown molding with its WALL CONTACT EDGE
against the guide fence and its CEILING CONTACT
EDGE against the crown molding stoppers as shown in
the figure. Adjust the crown molding stoppers according
to the size of the crown molding. Tighten the screws to
secure the crown molding stoppers. Refer to the table
(C) for the miter angle.
2
1
►
1.
Guide fence
2.
Crown molding stopper
(a)
(b)
(c)
(d)
1
2
1.
Inside corner
2.
Outside corner
Table (C)
–
Molding
position in
the figure
Miter angle
Finished
piece
For inside
corner
(a)
Right 45°
Save the right
side of blade
(b)
Left 45°
Save the left
side of blade
For outside
corner
(c)
Save the right
side of blade
(d)
Right 45°
Save the left
side of blade