Maytag MDB4651AWS Installation Instructions - Page 11

Using UL-listed/CSA

Get Maytag MDB4651AWS - 24 Inch Full Console Dishwasher PDF manuals and user guides View all Maytag MDB4651AWS manuals
Add to My Manuals
Save this manual to your list of manuals

Page 11 highlights

5, Using UL-listed/CSA approved twist-on connectors sized to connect power supply cord to 16-gauge dishwasher wire, connect the black wire from the power supply cord to the black wire on the terminal box. 6, Tighten the conduit connector screws to secure the power supply cord. 1, Measure the cabinet opening height. 7. Insert tabs on the left-hand side of the terminal box cover. 8. Using a V4"nut driver and previously removed screw, reinstall the terminal box cover with the wires inside terminal box. 2, Adjust the dishwasher leg height according to the following chart. Turn both of the leveler legs to the same height. Height (H) Adjusted Leg Height Height (X) (H) Adjusted Leg Height (X) 33W' (85.1 cm) 0" 338/8'' (85.4 cm) V8" (0.3 cm) 333/4'' (85.7 cm) V4" (0.6 cm) 337/8'' (86 cm) 3/8"(1 cm) 34" (86.4 cm) V2" (1.3 cm) 34V8" (86.7 cm) 8/8"(1.6 cm) 34V4" (87 cm) 3/4"(1.9 cm) 34%" (87.4 cm) 34W' (87.7 cm) 348/8'' (88 cm) 343/4'' (88.3 cm) 347/8'' (88.6 cm) 35" (88.9 cm) %" (2.2 cm) 1" (2.5 cm) 1V8" (2.8 cm) 1V4" (3.1 cm) 13/8"(3.5 cm) 1V2" (3.8 cm) \\ \ \ 9. Check that no wires are pinched by the cover. NOTE: Do not plug power supply cord into outlet until instructed. 11

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
5,
6,
Using UL-listed/CSA
approved
twist-on
connectors
sized to
connect
power supply
cord to 16-gauge
dishwasher
wire,
connect
the black wire from the power supply
cord to the
black wire on the terminal
box.
Tighten the conduit
connector
screws
to secure the power
supply
cord.
1,
Measure the cabinet
opening height.
7.
Insert tabs
on the left-hand
side of the terminal
box cover.
8.
Using a
V4"
nut driver and previously
removed
screw,
reinstall
the terminal
box cover with the wires inside terminal
box.
2,
Adjust the dishwasher
leg height according
to the following
chart. Turn both of the leveler legs to the same height.
Height
Adjusted
Leg
Height
Adjusted
Leg
(H)
Height
(X)
(H)
Height
(X)
33W'
(85.1 cm)
0"
34%" (87.4 cm)
%" (2.2 cm)
338/8
'' (85.4 cm)
V8"
(0.3 cm)
34W'
(87.7 cm)
1" (2.5 cm)
333/4
'' (85.7 cm)
V4"
(0.6 cm)
348/8
'' (88 cm)
1
V8"
(2.8 cm)
337/8
'' (86 cm)
3/8"(1 cm)
343/4
'' (88.3 cm)
1
V4"
(3.1 cm)
34" (86.4 cm)
V2"
(1.3 cm)
347/8
'' (88.6 cm)
13/8"(3.5 cm)
34V8" (86.7 cm)
8/8"(1.6 cm)
35" (88.9 cm)
1
V2"
(3.8 cm)
34V4" (87 cm)
3/4"(1.9 cm)
\\
\
\
9.
Check that no wires are pinched
by the cover.
NOTE: Do not plug power supply
cord into outlet until instructed.
11