Maytag MFC2061HEW Use and Care Guide - Page 6

Door Reinstallation - refrigerator model

Get Maytag MFC2061HEW - Bottom-Freezer Refrigerator PDF manuals and user guides
UPC - 719881157368
View all Maytag MFC2061HEW manuals
Add to My Manuals
Save this manual to your list of manuals

Page 6 highlights

Installation 4. Remove Phillips screw from each of the drawer slides (select models). 5. Lift top of drawer front to unhook the drawer from the slides. Lift door front out to remove. To Install: 1. Pull both rails out to full extension. 2. While supporting door front, hook supports into slots located on inside of each slide. Note: All four drawer bracket supports must be in the proper slots for the drawer to function properly. 3. Lower door front into final position. 4. Replace and tighten Phillips screws that were removed from the drawer slides (select models). 5. Place the basket cradles back onto the drawer slides. Align basket cradle snaps with the slots on the drawer brackets and press each cradle toward the bracket until it clicks. Basket cradle snap attachments 6. Tilt the lower basket front down and set it down into the basket cradles. Door Reinstallation Materials Needed: • Phillips screwdriver • 5⁄16" hex head driver 1. Install hinge assemblies: • Install center hinge with Phillips screws. 2. Place hinge side of refrigerator door on center hinge pin. • Install top hinge with 5⁄16" hex head screws. 3. While holding refrigerator door upright, tighten down top hinge with 5⁄16" hex head driver. 4. Reconnect two-pin connector. 5. Replace top hinge covers. 5

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
5
Door Reinstallation
Materials Needed:
•
Phillips screwdriver
•
5
±
16
” hex head driver
1.
Install hinge assemblies:
•
Install center hinge with Phillips
screws.
2. Place hinge side of refrigerator
door on center hinge pin.
•
Install top hinge with
5
±
16
” hex
head screws.
3. While holding refrigerator door
upright, tighten down top hinge
with
5
±
16
” hex head driver.
4. Reconnect two-pin connector.
5. Replace top hinge covers.
Installation
To Install:
1. Pull both rails out to
full extension.
2. While supporting door
front, hook supports
into slots located on
inside of each slide.
Note
:
All four drawer bracket supports must be in
the proper slots for the drawer to function properly.
6. Tilt the lower basket front down and set it down
into the basket cradles.
Basket cradle
snap attachments
3. Lower door front into final position.
4. Replace and tighten Phillips screws that were
removed from the drawer slides (select models).
4. Remove Phillips screw
from each of the drawer
slides (select models).
5. Lift top of drawer front to
unhook the drawer from
the slides. Lift door front
out to remove.
5. Place the basket cradles back onto the drawer
slides. Align basket cradle snaps with the slots on
the drawer brackets and press each cradle toward
the bracket until it clicks.