Miele Crystal G 5285 SCVi Operating and Installation manual - Page 40

Optimize Standby 40

Page 40 highlights

Additional options Optimize Standby A few minutes after the last button is pressed or a few minutes after the end of the program the dishwasher will switch to Standby mode to save energy. The time display and the indicator lights are turned off and only the K indicator light flashes slowly. If the dishwasher is not turned off after the program ends, after a few minutes in Standby mode it will turn off completely. You can also deactivate the Optimize Standby function. The time display and the indicator lights do not go out, and the dishwasher turns off 6 hours after the end of the program. This results in higher energy consumption. If Salt and/or Rinse aid or a fault is displayed, the dishwasher will not switch to Standby mode. ^ Open the door. ^ Press the K button to turn the dishwasher off. ^ Press and hold the Program button and simultaneously turn the dishwasher on using the K button. Keep the Program button pressed for at least four seconds until the lower right program indicator lights up. If it does not come on, start over. ^ Press the Turbo button eight times. The Turbo indicator light shows 8 short flashes in intervals. The flashing in the time display shows whether Optimizing Standby is turned on. - "p 1": Optimize Standby is on. - "p 0": Optimize Standby is off. ^ Press the Program button if you wish to change the setting. The setting is immediately saved. ^ Press the K button to turn the dishwasher off. 40

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64

Optimize Standby
A few minutes after the last button is
pressed or a few minutes after the end
of the program the dishwasher will
switch to Standby mode to save
energy. The time display and the
indicator lights are turned off and only
the
K
indicator light flashes slowly.
If the dishwasher is not turned off after
the program ends, after a few minutes
in Standby mode it will turn off
completely.
You can also deactivate the Optimize
Standby function. The time display and
the indicator lights do not go out, and
the dishwasher turns off 6 hours after
the end of the program.
This results in higher energy
consumption.
If Salt and/or Rinse aid or a fault is
displayed, the dishwasher will not
switch to Standby mode.
^
Open the door.
^
Press the
K
button to turn the
dishwasher off.
^
Press and hold the Program button
and
simultaneously
turn the
dishwasher on using the
K
button.
Keep the Program button pressed for
at least four seconds until the lower
right program indicator lights up.
If it does not come on, start over.
^
Press the Turbo button eight times.
The Turbo indicator light shows 8 short
flashes in intervals.
The flashing in the time display shows
whether Optimizing Standby is turned
on.
–"
p1
": Optimize Standby is on.
–"
p0
": Optimize Standby is off.
^
Press the Program button if you wish
to change the setting.
The setting is immediately saved.
^
Press the
K
button to turn the
dishwasher off.
Additional options
40