NEC VT695 NP115 : RS232 codes- Projectors
NEC VT695 - XGA LCD Projector Manual
 |
UPC - 050927253607
View all NEC VT695 manuals
Add to My Manuals
Save this manual to your list of manuals |
NEC VT695 manual content summary:
- NEC VT695 | NP115 : RS232 codes- Projectors - Page 1
on February 3, 2011 This file contains information about NEC projector control commands. Model Name GT60 : GT5000/GT6000 Series GT50 : GT1150/ NP600/NP600S Series VT : VT770 Series VT70 : VT37/VT47/VT480/VT57/VT570/VT575/VT670/VT676 Series VT80 : VT48/VT480/VT580 Series VT90 : VT49/VT490/ - NEC VT695 | NP115 : RS232 codes- Projectors - Page 2
control commands. 1. Serial connection using the serial port on the projector A serial cable is required. 2. USB connection using the USB port on the projector required. 3-3.LAN connection using the LAN port on the projector A LAN cable is required. 3-4. LAN connection using a wireless LAN unit - NEC VT695 | NP115 : RS232 codes- Projectors - Page 3
MT860/1060/1065/1075. * The GT5000/6000 does not come with a USB cable. * Note that a connection method using the supplied USB cable is not supported for the LT220/240/260. * The serial cable, LAN card and LAN cable are separately sold. * The WT610 replaced the WT610 and uses the same command set. - NEC VT695 | NP115 : RS232 codes- Projectors - Page 4
the projector and set the "idle mode". The projector cannot use the control commands in the standby mode. Setting method: Under projector [Projector Options] --> [Setup], ] STANDBY MODE: "POWER-SAVING" Control Command POWER ON Yes: Supported No: Not supported Serial Wired Wireless port LAN port - NEC VT695 | NP115 : RS232 codes- Projectors - Page 5
the controller to the projector is referred to as a command, and the one sent from the projector to | Bit | Bit | Bit |Bit| Bit | Bit | ~ | Bit | Bit | | | || | Data length Model code Projector ID ID2 ID1 * ID1: (8 Bit) This is an identification data assigned to each command - NEC VT695 | NP115 : RS232 codes- Projectors - Page 6
receives frames. Command : This specifies a model code for the projector that sends commands. (individual notification) Entering 0000B or 1111B becomes a common command for all the projectors. (broadcast notification) This is convenient for controlling multiple projectors at the same time. * When - NEC VT695 | NP115 : RS232 codes- Projectors - Page 7
code is set to "broadcast notification", the command becomes broadcast notification command, regardless of values of the projector ID. * Model code is specified using upper ranking 4 bits of data length. The lower ranking 4 bits becomes the upper bits of data length. * Data length : (12 Bit) - NEC VT695 | NP115 : RS232 codes- Projectors - Page 8
supported 00H : Unknown command 01H : The current model does not support this function. 02H : This model is not compatible with the Switcher. 03H : This model mode error occurs 00H : Available memory reservation error 01H : External control working 02H : Operating memory 03H : Standby 04H : On Forced - NEC VT695 | NP115 : RS232 codes- Projectors - Page 9
supported) Endpoint: Control transfer Endpoint 0 Device class: HID class (Ver1.1) USB1.1 Standard: Universal Serial Bus Specification Revision 1.1 HID : Human Interface Device Connector Specifications used. - For information on supported LAN cards, visit: Global: http://www.nec-pj.com/ [Port Number] - NEC VT695 | NP115 : RS232 codes- Projectors - Page 10
REQUEST 039. LAMP MODE SET 046. WXGA MODE SETTING REQUEST 049. WXGA MODE SETTING SET 050. REMOTE KEY CODE 060. GAIN PARAMETER REQUEST 2 077. MUTE CONTROL 078-1. SETTING REQUEST 078-2. RUNNING STATUS REQUEST 078-3. INPUT STATUS REQUEST 078-4. MUTE STATUS REQUEST 078-5. MODEL NAME REQUEST - NEC VT695 | NP115 : RS232 codes- Projectors - Page 11
STATUS REQUEST 079. FREEZE CONTROL 110. AUTO FUNCTIONS EXECUTE 111. AUTO ADJUST EXECUTE2 097-198. PIP/SIDE BY SIDE REQUEST 098-196. WXGA MODE SETTING SET 098-198. PIP/SIDE BY SIDE SET 305.1 BASE MODEL TYPE REQUEST 305.3 PROJECTOR INFORMATION REQUEST Availability by Model 1 2 3 4 5 6 7 8 9 10 11 12 - NEC VT695 | NP115 : RS232 codes- Projectors - Page 12
ID It is the value when forwarding a factory. This reflects the "Projector ID" that has been set to the projector. (*2) Model code: "xxH" inscription This will differ depending on the projector. In case of MT/NP1000 series In case of MT/NP3150 series In case of MT/NP3250 series In case of LT - NEC VT695 | NP115 : RS232 codes- Projectors - Page 13
0 = No execution (Normal condition) 1 = During execution Bit 4: External control mode 0 = OFF 1 = ON Bit 3: No Power-Off period 0 = Power-Off Possible (Normal condition) 1 = Power-Off Impossible Bit 2: Reserved Bit 1: Projector status 0 = Idling 1 = Power On Bit 0: Reserved Response: At the - NEC VT695 | NP115 : RS232 codes- Projectors - Page 14
Projector type See DATA70..71 08H : NP4000 Projector 11H : NP62 Projector DATA02 Projector ID DATA02 1 .. 64 NP4000 1 .. 254 NP62/NP64 1 .. 254 NP216 DATA03 Reserved DATA04 Projector (*5) 02H : VIDEO 03H : S-VIDEO 04H : COMPONENT 05H : Reserved 06H : DIGITAL (*6) 07H : VIEWER 08H : SLOT1 09H : - NEC VT695 | NP115 : RS232 codes- Projectors - Page 15
x : Not supported *1: Only LT240K/260K DATA34 Test pattern display 2 FFH: No display (Normal condition) FFH Other: Displaying Bit 2: BLUE pattern 0 = OFF 1 = ON Bit 1: GREEN pattern 0 = OFF 1 = ON Bit 0: RED pattern 0 = OFF 1 = ON DATA35 .. 50 Reserved DATA51 .. 65 User registration name ( 14 - NEC VT695 | NP115 : RS232 codes- Projectors - Page 16
00H : Idling 04H : Power On 05H : Cooling 06H : Idling (Error occurrence) Other than above: (nondisclosure) Internal use of code during a state transition period DATA70 .. 71 Projector type - NEC VT695 | NP115 : RS232 codes- Projectors - Page 17
Data01 01H 01H 01H 01H 02H 02H 02H 02H 02H 02H 03H 03H 03H 04H 04H 04H 04H 05H 05H 06H 06H 08H 08H 08H 10H 10H 10H 10H 10H 10H 10H 10H 10H 10H 10H 10H 10H 10H 10H 10H 11H 11H 11H 11H 11H 11H 11H 11H 12H 12H 12H 12H 12H 12H 12H 13H 13H 13H 13H 13H 13H 13H Data70 00H 01H 02H 00H 00H 01H 02H 00H 00H - NEC VT695 | NP115 : RS232 codes- Projectors - Page 18
DATA74 Entry list type 01H : Default 02H : User DATA75 .. 82 Reserved DATA83 On-screen mute 00H 1 (01H) 2 (02H) 2 (02H) 2 (02H) 4 (04H) Data08 RGB RGB VIDEO S-VIDEO COMPONENT COMPONENT DIGITAL DIGITAL VIEWER VIEWER SLOT1 SLOT1 SLOT2 SLOT2 VIDEO S-VIDEO VIEWER (01H) (01H) (02H) (03H) (04H) (04H - NEC VT695 | NP115 : RS232 codes- Projectors - Page 19
: This command acquires the error information occurring with the projector. Command: 00H 88H 00H 00H 00H 88H Response: At : None bit1 : FPGA error bit2 : Temperature error(Sensor) bit3 : Lamp(or Lamp1) housing error (!) bit4 : Lamp(or Lamp1) data error (!) bit5 : Mirror cover error bit6 : Lamp2 - NEC VT695 | NP115 : RS232 codes- Projectors - Page 20
does not accept the other command during power on processing. 016. POWER OFF Function: This command switches off the main power of the projector. Command: 02H 01H 00H 00H 00H 03H Response: At the time of a success 22H 01H 01H xxH 00H CKS (*1) (*2) (*3) Response: At the time of a failure - NEC VT695 | NP115 : RS232 codes- Projectors - Page 21
Component -- * * *- - - * - - - * 11H Component -- * - *- - - - * - - - 12H Component -- - - -- -* - - - - - 1AH DVI (*6) (!2) *- * - *- - * - - - - * 1AH DVI(DIGITAL HT1100 (!!!!) VT770 support Component and Viewer (!1) VT470/VT470JY/VT570/VT670/VT575/VT676/VT480/ - NEC VT695 | NP115 : RS232 codes- Projectors - Page 22
Supplement: * Picture mute is cancelled for the following: Input connector switching Video signal switching 021. PICTURE MUTE OFF Function: This command cancels the blank picture condition. Command: 02H 11H 00H 00H 00H 13H Response: At the time of a success 22H 11H 01H xxH 00H CKS (*1) (*2) - NEC VT695 | NP115 : RS232 codes- Projectors - Page 23
A2H 13H 01H xxH 02H DATA01 DATA02 CKS (*1) (*2) (*4) (*3) 024. ONSCREEN MUTE ON Function: This command blanks the on-screen display. Command: 02H 14H 00H 00H 00H 16H Response: At the time of a success 22H 14H 01H xxH 00H CKS (*1) (*2) (*3) Response: At the time of a failure A2H 14H 01H - NEC VT695 | NP115 : RS232 codes- Projectors - Page 24
*tint increment/decrement brightness contrast color tint sharpness Not supported "LT170","VT60 series","VT70 series","VT80 series", "VT90 series" Not supported "HT410/HT510","LT180/LT25/LT30/LT35" volume Not supported "LT170","VT60 series","VT70 series" (except "VT80 series, VT90 series") Not - NEC VT695 | NP115 : RS232 codes- Projectors - Page 25
05H fixed DATA02 Setting items 00H : Volume 01H : Bass 02H : Treble 03H : Balance DATA03 Setting mode 00H : Absolute value specification 01H : Relative value specification DATA04 DATA05 Setting Value (Lower ranking 8 bits) Setting Value (Upper ranking 8 bits) Response: At the time of a success - NEC VT695 | NP115 : RS232 codes- Projectors - Page 26
DATA05 Adjustment value (Upper ranking 8 bits) Response: At the time of a success 23H 10H 01H xxH 02H DATA01 DATA02 CKS (*1) (*2) (*3) Data Portion Contents DATA01 .. 02 Results 0000H : Normal 0000H Other : Error Response: At the time of a failure A3H 10H 01H xxH 02H DATA01 DATA02 CKS (*1) - NEC VT695 | NP115 : RS232 codes- Projectors - Page 27
name (NULL termination character string) DATA50 .. 82 : Reserved DATA83 .. 86 : Lamp Hour Meter (second) (!) DATA87 .. 90 : Filter Usage (second) DATA91 .. 94 : Panel Usage (second) DATA95 .. 98 : Projector Usage (second) Response: At the time of a failure A3H 8AH 01H xxH 02H DATA01 DATA02 - NEC VT695 | NP115 : RS232 codes- Projectors - Page 28
: At the time of a failure A3H 8CH 01H xxH 02H DATA01 DATA02 CKS (*1) (*2) (*4) (*3) Supplement: Example for acquiring remaining lamp time (in terms of Normal mode values) : Lamp Hour Meter (Normal mode) DATA01 DATA02 DATA03 DATA04 30H 2AH 00H 00H : 10800 seconds Calculator Procedure 1) Set - NEC VT695 | NP115 : RS232 codes- Projectors - Page 29
information on the projector lamp in Eco mode. Command: 03H 96H 00H 00H 02H DATA01 DATA02 CKS (*3) Data Portion Contents DATA01 Target 00H : Lamp1 01H : Lamp2 DATA02 item 00H : Lamp Hour Meter (second) (!) 01H : Lamp usage time (second) (!!) 04H : lamp remaining amount until lamp warning message - NEC VT695 | NP115 : RS232 codes- Projectors - Page 30
= 360000/ 3600= 100 hours (!) Lamp Hour Meter This is the timer for normal lamp mode conversion. (!!) Lamp usage time This is the lamp total usage. It is displayed in the projector's menu. (!!!) NP4000/4001, NP4100/4100W : This function is not supported. 037-7. LAMP INFORMATION REQUEST 4 Function - NEC VT695 | NP115 : RS232 codes- Projectors - Page 31
Use Prohibited Time 2100[H] A Lamp Use Warning Starting Time 2000[H] Model. X = 100 - ((2100 * 100) / 2000) = -5[%] (!2) Lamp Hour Meter This is the timer for normal lamp mode conversion. (!3) Lamp usage time This is the lamp total usage. It is displayed in the projector's menu. (!4) This setting is - NEC VT695 | NP115 : RS232 codes- Projectors - Page 32
Function: This command sets the lamp mode of projector. Command: 03H B1H 00H 00H 02H DATA01 DATA02 CKS (*3) 046. WXGA MODE SETTING REQUEST Function: This command acquires the setting of the WXGA Mode of projector. Command: 03H B0H 00H 00H 01H C3H 77H Response: At the time of a success 23H B0H - NEC VT695 | NP115 : RS232 codes- Projectors - Page 33
049. WXGA MODE SETTING SET Function: This command sets the WXGA Mode of projector. Command: 03H B1H 00H 00H 02H DATA01 DATA02 CKS (*3) Data Portion Contents DATA01 C3H fixed DATA02 Setting Value 00H : OFF 01H : ON Response: At the - NEC VT695 | NP115 : RS232 codes- Projectors - Page 34
command. This current model does not support this function. Invalid values specified. Specified terminal is unavailable or cannot be selected. Setting not possible. Power Off inhibited. 050. REMOTE KEY CODE Function: This command sends remote control key codes of projector. Command: 02H 0FH - NEC VT695 | NP115 : RS232 codes- Projectors - Page 35
SOURCE (!!) 216 D8H 00H RGB(*5) oggle (!!) 217 D9H 00H VIDEO Toggle (!!) 218 DAH 00H 3D REFORM RESET 221 DDH 00H AUTO (SHORT) 222 DEH 00H AUTO (LONG) 223 DFH 00H PICTURE MANAGEMENT (!!) 225 E1H 00H COMPONENT (!!) 226 E2H 00H ZOOM POS UP (HT) 227 E3H 00H ZOOM POS DOWN (HT) 228 E4H - NEC VT695 | NP115 : RS232 codes- Projectors - Page 36
PSCODE(Passcode screen will be displayed at once) 238 EEH 00H LAMP MODE (!!!) Response: At the time of a success 22H 0FH About AUTO key The MT series model with the built-in image sensor does not support the AUTO key. Use the AUTO menu functionality (digits 0-9, cursor movement, enter, select, return - NEC VT695 | NP115 : RS232 codes- Projectors - Page 37
051. CARBON SAVINGS INFORMATION REQUEST Function: This command acquires the Carbon Saving values on the projector. Command: 03H 9AH 00H 00H 01H DATA01 CKS (*3) Data Portion Contents DATA01 Acquirement items 00H : Total Carbon Savings 01H : Carbon Savings during operation Response: At - NEC VT695 | NP115 : RS232 codes- Projectors - Page 38
Function: This command acquires the adjustment values. Command: 03H 04H 00H 00H 03H DATA01 .. DATA03 CKS (*3) Data Portion Contents DATA01 .. 02 Acquirement items (!) DATA03 00H fixed Response: At the time of a success 23H 04H 01H xxH 0DH DATA01 .. DATA13 CKS (*1) (*2) (*3) Data - NEC VT695 | NP115 : RS232 codes- Projectors - Page 39
Adjust Phase 00H Image / Video Filter 00H Image / Resolution 00H Image Black Correct / Inv Gain 00H Lamp Output 00H Signal Level / Auto Control 00H Signal Level / R/G/B Gain 08H Color Correct / V Gain 00H HD Delay 00H Ref. Pedestal Level / U 00H Setup Level 01H Setup Level / Adjust 02H Setup Level - NEC VT695 | NP115 : RS232 codes- Projectors - Page 40
/ Vertical 02H Pincushion / Balance 00H Digital Zoom / Zoom 01H Digital Zoom / Horizontal Position 02H Digital Zoom / Vertical Position 00H White Bal. SweetVision Level 94H 00H Vertical Enhancer 95H 00H I/P Converter 96H 00H Lamp Mode Adjust 97H 00H Wall Color Command example: * In case of - NEC VT695 | NP115 : RS232 codes- Projectors - Page 41
077. MUTE CONTROL Function: This command controls the mute of picture, sound and on-screen. Command: signal switching Volume adjustment 078-1. SETTING REQUEST Function: This command acquires the function information of projector. Command: 00H 85H 00H 00H 01H 00H 86H Response: At the time of a - NEC VT695 | NP115 : RS232 codes- Projectors - Page 42
DATA01 DATA02 DATA03 01H 00H 03H MT1060/MT1065 01H 01H 03H MT860 01H 02H 03H MT1075 01H 00H 06H NP1000/NP2000 02H 00H 03H LT240/LT260 02H 01H 03H LT220 02H 02H 03H LT240K/LT260K 02H 00H 05H LT245/LT265 02H 00H 06H LT380 02H 01H 06H LT280 03H 00H 06H VT80 Series 03H - NEC VT695 | NP115 : RS232 codes- Projectors - Page 43
time of a failure A0H 85H 01H xxH 02H DATA01 DATA02 CKS (*1) (*2) (*4) (*3) 078-2. RUNNING STATUS REQUEST Function: This command acquires the status of the projector operation. Command: 00H 85H 00H 00H 01H 01H 87H Response: At the time of a success 20H 85H 01H xxH 10H DATA01 .. DATA16 CKS - NEC VT695 | NP115 : RS232 codes- Projectors - Page 44
the projector. Component 03H 04H DVI(*6) 01H 06H DVI(DIGITAL)(*6) 01H 06H HDMI 01H 06H Viewer 01H 07H LAN 02H 07H Slot1-1 01H 08H Slot1-2 02H 08H Slot2-1 01H 09H Slot2-2 02H 09H RGB(Video) 02H 02H RGB(S-Video) 02H 03H DATA05 Entry list type 01H : Default 02H : User - NEC VT695 | NP115 : RS232 codes- Projectors - Page 45
A0H 85H 01H xxH 02H DATA01 DATA02 CKS (*1) (*2) (*4) (*3) 078-4. MUTE STATUS REQUEST Function: This command acquires the status of the mute of projector. Command: 00H 85H 00H 00H 01H 03H 89H Response: At the time of a success 20H 85H 01H xxH 10H DATA01 .. DATA16 CKS (*1) (*2) (*3) Data - NEC VT695 | NP115 : RS232 codes- Projectors - Page 46
model name of the projector. Command: 00H 85H 00H 00H 01H 04H 8AH Response: At the time of a success 20H 85H 01H xxH 20H DATA01 .. DATA32 CKS (*1) (*2) (*3) Data Portion Contents DATA01 .. 32 Model 02H Unknown command The current model does not support this function. Unvalid values specified - NEC VT695 | NP115 : RS232 codes- Projectors - Page 47
[079. FREEZE CONTROL Function: This command controls the freeze. Command: 01H 98H 00H 00H 01H DATA01 (*3) 097-196.WXGA MODE SETTING REQUEST Function: This command acquires the setting of the WXGA Mode of projector. Command: 03H B0H 00H 00H 01H C3H 77H Response: At the time of a success 23H B0H - NEC VT695 | NP115 : RS232 codes- Projectors - Page 48
01H xxH 02H DATA01 DATA02 CKS (*1) (*2) (*4) (*3) 098-198. PIP/SIDE BY SIDE SET Function: This command sets the PIP/SIDE BY SIDE of projector. Command: 03H B1H 00H 00H 03H DATA01 DATA02 DATA03 CKS Data Portion Contents DATA01 C5H fixed DATA02 Update target 00H : MODE 01H : POSITION - NEC VT695 | NP115 : RS232 codes- Projectors - Page 49
functions. Command: 03H B6H 00H 00H 01H DATA01 CKS (*3) Data Portion Contents DATA01 Execution items Focus 00H ! 01H * !: According to projector setting *: Executing Response: At the time of a success 23H B6H 01H xxH 02H DATA01 DATA02 CKS (*1) (*2) (*3) Data Portion Contents DATA01 - NEC VT695 | NP115 : RS232 codes- Projectors - Page 50
00H CKS (*1) (*2) (*3) Response: At the time of a failure A3H BAH 01H xxH 02H DATA01 DATA02 CKS (*1) (*2) (*4) (*3) 305-1. BASE MODEL TYPE REQUEST Function: This command acquires the projector type. Command: 00H BFH 00H 00H 01H 00H C0H Response: At the time of a success 20H BFH 01H xxH - NEC VT695 | NP115 : RS232 codes- Projectors - Page 51
DATA02 DATA03 DATA13 DATA14 00H 01H 00H 03H MT1060/1065 00H 01H 02H 03H MT860 00H 01H 02H 03H MT1075 00H 01H 00H 06H NP1000/NP2000 00H 02H 00H 03H LT240/LT260 00H 02H 01H 03H LT220 00H 02H 02H 03H LT260K 00H 02H 00H 05H LT245/LT265 00H 02H 00H 06H LT380 00H 02H - NEC VT695 | NP115 : RS232 codes- Projectors - Page 52
Projector Processing Status 00H : Idle 04H : Power On 05H : Cooling 06H : Idle(Error Standby) Other : Not Support displaying 04H : LAN displaying 05H : Test Pattern (User) displaying 10H : Signal selection in progress Other : Not Support DATA04 Select source input type 1 01H : 1 - NEC VT695 | NP115 : RS232 codes- Projectors - Page 53
B/W60 x6H : B/W50 x7H : PALNM x8H : NTSC3.58 LBX x9H : NTSC3.58 SQZ xAH : COMPONENT(60Hz) xBH : COMPONENT(50Hz) xCH : Un known xDH : NTSC xEH : PAL-M xFH : PAL-N FFH : Not Video Input Other : Not Support DATA07 Picture Mute 00H : OFF 01H : ON DATA08 Sound Mute 00H : OFF 01H : ON - NEC VT695 | NP115 : RS232 codes- Projectors - Page 54
6. Data Portion of Response DATA01 DATA02 Error types Error description Error contents 00H 00H Unknown command 00H 01H The current model does not support this function. 01H 00H Unvalid values specified. 01H 01H Specified terminal is unavailable or cannot be selected. 01H 02H
-
1 -
2 -
3 -
4 -
5 -
6 -
7 -
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
-
17
-
18
-
19
-
20
-
21
-
22
-
23
-
24
-
25
-
26
-
27
-
28
-
29
-
30
-
31
-
32
-
33
-
34
-
35
-
36
-
37
-
38
-
39
-
40
-
41
-
42
-
43
-
44
-
45
-
46
-
47
-
48
-
49
-
50
-
51
-
52
-
53
-
54
 |
 |
======================================================================
Control Commands for NEC Projector (Basic) Rev 02.03.11a
Copyright (C) NEC Display Solutions, Ltd. 2002-2010
----------------------------------------------------------------------
Updated on February 3, 2011
----------------------------------------------------------------------
This file contains information about NEC projector control commands.
Model Name
GT60
: GT5000/GT6000 Series
GT50
:
GT1150/GT2150 Series
HT
: HT1000/HT1100 Series
HT10
: HT410/HT510 Series
LT180
LT180
LT30
: LT25/LT30/LT35 Series
LT
:
LT220/LT240/LT240K/LT260/LT260K/LT245/LT265 Series
LT80
: LT280/LT380 Series
MT70
: MT860/MT1060/MT1065/MT1075 Series
NP60
:
NP40/NP50/NP60 Series
NP62
:
NP41/NP61/NP62 Series
NP1000
: NP1000/NP2000 Series
NP3150
: NP1150/NP2150/NP3150/NP3151W Series
NP4000
:
NP4000/NP4001 Series
NP905
: NP905/NP901W/VT800 Series
NP600
:
NP300/NP400/NP500/NP500W/NP500WS/NP600/NP600S Series
VT
:
VT770 Series
VT70
:
VT37/VT47/VT480/VT57/VT570/VT575/VT670/VT676 Series
VT80
:
VT48/VT480/VT580 Series
VT90
:
VT49/VT490/VT590/VT595/VT695 Series
VT700
:
VT700
WT
: WT600/WT610/WT615 Series
NP4100
:
NP4100/NP4100W Series
NP3250
: NP1250/NP2250/NP3250/NP3250W Series
NP610
:
NP310/NP410/NP410W/NP510/NP510W/NP510WS/NP610/NP610S Series
NP2200
:
NP1200/NP2200 Series
NP216
:
NP110/NP115/NP215/NP216 Series
NP64
:
NP43/NP64 Series
M300:
M260X/M260W/M300X/M300W Series
P420
P350X/P350W/P420X Series
======================================================================
Contents
1. Projector Control
2. Connection Method
3. Interface Conditions
4. List of Commands
5. Command Descriptions
6. Table of Response Error Codes
======================================================================
1. Projector Control
----------------------------------------------------------------------
NEC projectors make use of control commands that control the functions of the projector via connection with a
personal computer or another device.