NEC VT695 NP115 : RS232 codes- Projectors - Page 4

P350X/P350W/P420X Series], STANDBY MODE: POWER-SAVING, Control Command, Serial, Wired, LAN port, - front projector

Get NEC VT695 - XGA LCD Projector PDF manuals and user guides
UPC - 050927253607
View all NEC VT695 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 4 highlights

(CAUTION) Before making connections, be sure to invalidate the standby mode of the projector and set the "idle mode". The projector cannot use the control commands in the standby mode. Setting method: Under projector [Projector Options] --> [Setup], enter a check for [Idle Mode] on Page 4. ( CAUTION ) (!1) Before making connections, be sure to select [NORMAL] for [STANDBY MODE]. Setting method : From the projector's menu, select [SETUP] --> [OPTIONS(2)] -->[STANDBY MODE]--> [NORMAL]. ( CAUTION ) (!2) The projector accept the "POWER ON" command during [POWER-SAVING] mode for[STANDBY MODE]. Supplement: (!1) Only the NP600/NP610/NP3200 series is compatible. (!2) Only the M300 series is compatible. [P350X/P350W/P420X Series] STANDBY MODE: "POWER-SAVING" Control Command POWER ON Yes: Supported No: Not supported Serial Wired Wireless port LAN port LAN unit Yes No No 3. Interface Conditions Serial connection The communications method conforms to the RS-232C standard. Baud rate: Data length: Parity bit: Stop bits: Communications mode: 38400 bps (NP600 series, NP610 Series, VT60/VT70/VT80/VT90 series, VT700: 19200bps) 8 bits No parity 1 bit Full duplex The control connector is described below. [ HT/LT/NP40/VT70/VT80/VT90/WT ] The PC CONTROL connector is a mini DIN 8-pin connector. 1 To TxD of PC 2 3 4 To GND of PC 5 6 7 To RxD of PC 8 * 2, 3, 5, 6, and 8 are used inside the projector. [ GT/LT80/MT/NP1000/VT (except VT70/VT80/VT90) ] The PC CONTROL connector is a D-SUB 9-pin connector.

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
(CAUTION)
Before making connections, be sure to invalidate the standby mode of the projector and set the "idle mode". The
projector cannot use the control commands in the standby mode.
Setting method: Under projector [Projector Options] --> [Setup], enter a check for [Idle Mode] on Page 4.
( CAUTION ) (!1)
Before making connections, be sure to select [NORMAL] for [STANDBY MODE].
Setting method : From the projector's menu, select [SETUP] --> [OPTIONS(2)] -->[STANDBY MODE]--> [NORMAL].
( CAUTION ) (!2)
The projector accept the "POWER ON" command during [POWER-SAVING] mode for[STANDBY MODE].
Supplement:
(!1) Only the NP600/NP610/NP3200 series is compatible.
(!2) Only the M300 series is compatible.
[P350X/P350W/P420X Series]
STANDBY MODE: "POWER-SAVING"
Control Command
Serial
port
Wired
LAN port
Wireless
LAN unit
POWER ON
Yes
No
No
Yes:
Supported
No: Not supported
====================================================================
3. Interface Conditions
----------------------------------------------------------------------
Serial connection
----------------------------------------------------------------------
The communications method conforms to the RS-232C standard.
Baud rate:
38400 bps
(NP600 series, NP610 Series, VT60/VT70/VT80/VT90 series, VT700: 19200bps)
Data length:
8 bits
Parity bit:
No parity
Stop bits:
1 bit
Communications mode:
Full duplex
The control connector is described below.
[ HT/LT/NP40/VT70/VT80/VT90/WT ]
The PC CONTROL connector is a mini DIN 8-pin connector.
1
To TxD of PC
2
3
4
To GND of PC
5
6
7
To RxD of PC
8
* 2, 3, 5, 6, and 8 are used inside the projector.
[ GT/LT80/MT/NP1000/VT (except VT70/VT80/VT90) ]
The PC CONTROL connector is a D-SUB 9-pin connector.