Nady MHT-16 Manual - Page 6

Quick MGT-16 User Controls/Connections Guide

Get Nady MHT-16 PDF manuals and user guides View all Nady MHT-16 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 6 highlights

Quick MGT-16 User Controls/Connections Guide MT-16A/R Instrument Transmitter 17. POWER SWITCH Slide in arrow direction to power transmitter On 18. 15dB ATTENUATION PAD Select to reduce the input gain by 15dB for higher level 19 audio input signals 19. INPUT ¼" PLUG Connect directly intoguitar/bass output jack 20. POWER & LOW BATTERY LED Flashes once at power up, continous flashing indicates battery needs replacement 20 21. IR RECEPTOR SENSOR/WINDOW Infrared LED sensor for linking the TX to the RX 18 during IR frequency download 17 21 22. BATTERY COMPARTMENT Insert one AAA battery, observing correct polarity 22 23. INTERNAL AUDIO LEVEL ADJUST Remove battery to access slot and adjust 23 internal trim-pot with small screwdriver for optimal input level setting. Note: this is to be done only in rare cases as factory level setting is already optimized for most guitars and basses 24 and 15dB Pad also available.Note: Set control carefully. If trim-pot is turned past minimum 26 and maximum adjustment points it may need to be backed up to achieve desired setting. 24. ANTENNA Permanently attached flexible antenna 25 25. BATTERY Single AAA alkaline or NiMH battery required for operation 26. BATTERY COMPARTMENT COVER Slide to open ASCTM IR Sync Download of Selected Frequency of MGT-16 Receiver to MT-16A/R, MH-16, LK-16 or WH-16 Transmitter (1) ASC™ IR SYNC INFRARED LED WINDOW For downloading selected Channel (Frequency) to transmitter (21, 31, 46, 56) MT-16A/R, MH-16, LK-16, WH-16 TRANSMITTER IR RECEPTOR SENSOR/WINDOW Infrared LED sensor for linking the TX to the RX during IR frequency download. (14) ASC™ IR SYNC BUTTON Press to make the IR link download the receiver's selected frequency to the TX. First, turn on the system transmitter supplied (or turn off and then on again if already on) and position its IR window 6-12" away from the RX IR window, press the SYNC button once and wait one second for the RX to respond. If the IR data download is successful, the receiver SIGNAL LED (10) will light indicating the transmitter is locked in and transmitting. 6

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
Quick MGT-16 User Controls/Connections Guide
MT-16A/R Instrument Transmitter
ASC
TM
IR Sync Download of Selected
Frequency of MGT-16 Receiver to
MT-16A/R, MH-16, LK-16 or WH-16
Transmitter
(1)
ASC
™
IR SYNC INFRARED LED WINDOW
For downloading selected Channel
(Frequency) to transmitter
(21, 31, 46, 56)
MT-16A/R, MH-16, LK-16, WH-16
TRANSMITTER IR RECEPTOR SENSOR/WINDOW
Infrared LED sensor for linking the TX to the RX
during IR frequency download.
(14)
ASC
™
IR SYNC BUTTON
Press to make the IR link
download the receiver’s selected frequency to the TX.
First, turn on the system transmitter supplied (or turn
off and then on again if already on) and position its
IR window 6-12” away from the RX IR window, press
the SYNC button once and wait one second for the RX
to respond. If the IR data download is successful, the
receiver
SIGNAL LED (10)
will light indicating the
transmitter is locked in and transmitting.
17
18
19
20
21
22
23
26
25
24
17.
POWER SWITCH
Slide in arrow direction
to power transmitter On
18.
15dB ATTENUATION PAD
Select to
reduce the input gain by 15dB for higher level
audio input signals
19.
INPUT ¼” PLUG
Connect directly
intoguitar/bass output jack
20.
POWER &
LOW BATTERY LED
Flashes
once at power up, continous flashing indicates
battery needs replacement
21.
IR RECEPTOR SENSOR/WINDOW
Infrared LED sensor for linking the TX to the RX
during IR frequency download
22.
BATTERY COMPARTMENT
Insert one AAA
battery, observing correct polarity
23.
INTERNAL AUDIO LEVEL ADJUST
Remove battery to access slot and adjust
internal trim-pot with small screwdriver for
optimal input level setting.
Note: this is to be
done only in rare cases as factory level setting
is already optimized for most guitars and basses
and 15dB Pad also available.Note: Set control
carefully. If trim-pot is turned past minimum
and maximum adjustment points it may need to
be backed up to achieve desired setting.
24.
ANTENNA
Permanently attached flexible
antenna
25.
BATTERY
Single AAA alkaline or NiMH
battery required for operation
26.
BATTERY COMPARTMENT COVER
Slide
to open
6