Home » Netgear Manuals » Hubs & Switches » Netgear GS728TPP » Manual Viewer

Netgear GS728TPP GS728TP/GS728TPP/GS752TP Hardware Installation Guide - Page 25

Step 8: Manage the Switch Using a Web Browser or the Computer Utility, The GS752TP, GS728TP - default ip address

Add to My Manuals
Save this manual to your list of manuals

Page 25 highlights

GS752TP, GS728TP, and GS728TPP Gigabit Smart Switch Step 8: Manage the Switch Using a Web Browser or the Computer Utility The GS752TP, GS728TP, and GS728TPP Gigabit Smart Switch contains software for viewing, changing, and monitoring the way it works. This management software is not required for the switch to work. You can use the switch without using the management software. However, the management software enables the setup of VLAN and trunking features and also improves the efficiency of the switch, which results in the improvement of its overall performance as well as the performance of the network. After powering up the switch for the first time, the Smart Switch can be configured using a web browser or a program called Smart Control Center. For more information about managing the switch, see the software administration manual on the Smart Switch resource CD. Note: The switch is configured with a default IP address of 192.168.0.239 and a subnet mask of 255.255.255.0. 26

Section	Page
ProSafe® GS752TP, GS728TP, and GS728TPP Gigabit Smart Switches	1
Contents	3
1. Introduction	5
Overview	6
Features	6
Package Contents	8
2. Physical Description	9
GS752TP Front Panel and Back Panel Configuration	10
GS728TP Front Panel and Back Panel Configuration	11
GS728TPP Front Panel and Back Panel Configuration	12
LED Designations	14
Port LEDs	14
System LEDs	15
Device Hardware Interfaces	16
RJ-45 Ports	16
SFP Ports	16
Reset Button	17
Factory Defaults Button	17
Select Button	17
3. Applications	18
Desktop Switching	18
Backbone Switching	19
4. Installation	20
Step 1: Prepare the Site	21
Step 2: Install the Switch	21
Install the Switch on a Flat Surface	21
Install the Switch in a Rack	21
Step 3: Check the Installation	22
Step 4: Connect Devices to the Switch	23
Step 5: Install an SFP Transceiver Module	23
Step 6: Apply AC Power	24
Step 7: Apply RPS DC Power	24
Step 8: Manage the Switch Using a Web Browser or the Computer Utility	25
A. Troubleshooting	26
Troubleshooting Chart	27
Additional Troubleshooting Suggestions	27
Network Adapter Cards	27
Configuration	27
Switch Integrity	28
Autonegotiation	28
B. Technical Specifications	29
Network Protocol and Standards Compatibility	29
Management	29
Interface	30
LEDs	30
Performance Specifications	30
Power Supply	31
Physical Specifications	31
Environmental Specifications	32
Electromagnetic Emissions	32
Safety	32
C. Notification of Compliance	33

Match case Limit results 1 per page

GS752TP, GS728TP, and GS728TPP Gigabit Smart Switch

Step 8: Manage the Switch Using a Web Browser or the

Computer Utility

The GS752TP, GS728TP, and GS728TPP Gigabit Smart Switch contains software for

viewing, changing, and monitoring the way it works. This management software is not

required for the switch to work. You can use the switch without using the management

software. However, the management software enables the setup of VLAN and trunking

features and also improves the efficiency of the switch, which results in the improvement of

its overall performance as well as the performance of the network.

After powering up the switch for the first time, the Smart Switch can be configured using a

web browser or a program called Smart Control Center. For more information about

managing the switch, see the software administration manual on the Smart Switch resource

CD.

Note:

The switch is configured with a default IP address of 192.168.0.239

and a subnet mask of 255.255.255.0.