Netgear WMS5316 WMS5316 Reference Manual - Page 23

Adding Access Points, Wireless Management System does not recognize, though this is not common. See - discovery

Get Netgear WMS5316 - ProSafe 16-AP Wireless Management System PDF manuals and user guides
UPC - 606449068436
View all Netgear WMS5316 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 23 highlights

ProSafe 16 AP Wireless Management System WMS5316 Reference Manual • If discovery results show unknown access points, it could be due to these reasons: - The access point is running an older version of firmware. Upgrade firmware as needed so that discovery can locate the access point. - The Wireless Management System located a NETGEAR access point that is not supported or located a NETGEAR device that is not an access point. For a list of compatible access point models and their supported firmware, see "Compatible Access Point Supported Firmware Versions" in Appendix A. • If a new NETGEAR access point is not discovered, it might have a MAC address that the Wireless Management System does not recognize, though this is not common. See "Using Discovery OUI" on page 7-15. Adding Access Points After the Wireless Management System discovers the access points, add them so they can be managed by the Wireless Management System. 1. On the Access Point Discovery page, select the access point and click Add. Figure 2-3 Access Point Discovery 2-4 v1.0, March 2010

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
ProSafe 16 AP Wireless Management System WMS5316 Reference Manual
Access Point Discovery
2-4
v1.0, March 2010
•
If discovery results show unknown access points, it could be due to these reasons:
–
The access point is running an older version of firmware. Upgrade firmware as needed so
that discovery can locate the access point.
–
The Wireless Management System located a NETGEAR access point that is not supported
or located a NETGEAR device that is not an access point.
For a list of compatible access point models and their supported firmware, see
“Compatible
Access Point Supported Firmware Versions” in Appendix
A
.
•
If a new NETGEAR access point is not discovered, it might have a MAC address that the
Wireless Management System does not recognize, though this is not common. See
“Using
Discovery OUI” on page
7-15
.
Adding Access Points
After the Wireless Management System discovers the access points, add them so they can be
managed by the Wireless Management System.
1.
On the Access Point Discovery page, select the access point and click
Add
.
Figure
2-3