Netgear WMS5316 WMS5316 Reference Manual - Page 68

Upgrading Access Point Firmware, Brows, Apply, Warning - firmware upgrade

Get Netgear WMS5316 - ProSafe 16-AP Wireless Management System PDF manuals and user guides
UPC - 606449068436
View all Netgear WMS5316 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 68 highlights

ProSafe 16 AP Wireless Management System WMS5316 Reference Manual 4. On the Upgrade page, click Browse. 5. Locate and select the file you downloaded. 6. Click Apply to send the software to the Wireless Management System. This loads the new software into the Wireless Management System and causes the Wireless Management System to restart. Note: Do not try to go online, turn off the Wireless Management System, shut down the computer or do anything else to the Wireless Management System until it finishes restarting! When the Test light turns off, wait a few more seconds before doing anything. 7. Check the Monitoring page to see the firmware version to verify that the new software is installed. Upgrading Access Point Firmware You can install a new version of the access point's firmware using the Access Point Upgrade page. Warning: In some cases, such as a major upgrade, you may need to erase the configuration of your access point after upgrading it. See the Release Notes included with the software to find out if you need to reconfigure the access point. Reconfiguring access points already managed by the Wireless Management System requires only the IP address to be set manually. The Wireless Management System restores configuration for already managed access points running supported software version. To upgrade the access point software: 1. Go to the NETGEAR website at www.NETGEAR.com customer service downloads section to get new versions of the access point software for supported models. After downloading an upgrade file, you may need to unzip (uncompress) it before upgrading the access point. Warning: Once you click Upload do NOT interrupt the process of sending the software to the access point and restarting the access point. 2. Download the new software for a specific access point model to upgrade. 7-10 v1.0, March 2010 Maintenance

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
ProSafe 16 AP Wireless Management System WMS5316 Reference Manual
7-10
Maintenance
v1.0, March 2010
4.
On the Upgrade page, click
Brows
e.
5.
Locate and select the file you downloaded.
6.
Click
Apply
to send the software to the Wireless Management System.
This loads the new software into the Wireless Management System and causes the Wireless
Management System to restart.
Note:
Do not try to go online, turn off the Wireless Management System, shut down
the computer or do anything else to the Wireless Management System until it
finishes restarting! When the Test light turns off, wait a few more seconds
before doing anything.
7.
Check the Monitoring page to see the firmware version to verify that the new software is
installed.
Upgrading Access Point Firmware
You can install a new version of the access point’s firmware using the Access Point Upgrade page.
Warning:
In some cases, such as a major upgrade, you may need to erase the
configuration of your access point after upgrading it.
See the Release Notes included with the software to find out if you need to reconfigure the access
point. Reconfiguring access points already managed by the Wireless Management System requires
only the IP address to be set manually. The Wireless Management System restores configuration
for already managed access points running supported software version.
To upgrade the access point software:
1.
Go to the NETGEAR website at
www.NETGEAR.com
customer service downloads section to
get new versions of the access point software for supported models. After downloading an
upgrade file, you may need to unzip (uncompress) it before upgrading the access point.
Warning:
Once you click Upload do NOT interrupt the process of sending the
software to the access point and restarting the access point.
2.
Download the new software for a specific access point model to upgrade.