Nikon 9282 User Manual - Page 113

Film That Must Be Repaired Before Use

Get Nikon 9282 - Super Coolscan 4000 ED PDF manuals and user guides
UPC - 018208092826
View all Nikon 9282 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 113 highlights

Film That Must Be Repaired Before Use Film with the defects listed below must be repaired before it can be scanned in the SA-21. It can be scanned without preparation using the FH-3 film holder with the MA-20 (S) slide-mount adapter ( 105). Problem Solution There is tape on the ends of the film. Remove the tape or trim the ends of the film with scissors. After removing tape, wipe off all traces of adhesive with a soft, dry cloth, being careful not to damage the film. Film is cut on an angle or torn. Trim the end of film straight across, being careful not to cut across the perforations. The final perforation has been cut or torn. Trim the film straight across, being careful not to cut across the remaining perforations. If the film can not be trimmed without cutting across the image in the frame, trim only the outer edge from the perforation as shown above at left. Before scanning, remove dirt and dust from the film and perforations with a blower and wipe off fingerprints with a dry, soft cloth, being careful not to scratch the film. 103

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
103
Problem
Solution
There is tape on the ends of the film.
Remove the tape or trim the ends of the film with
scissors.
After removing tape, wipe off all traces of
adhesive with a soft, dry cloth, being careful not to
damage the film.
Film is cut on an angle or torn.
Trim the end of film straight across, being careful
not to cut across the perforations.
Before scanning, remove dirt and dust from the film and perforations with a blower and wipe off
fingerprints with a dry, soft cloth, being careful not to scratch the film.
Film That Must Be Repaired Before Use
Film with the defects listed below must be repaired before it can be scanned in the SA-21.
It
can be scanned without preparation using the FH-3 film holder with the MA-20 (S) slide-mount
adapter (
105).
Trim the film straight across, being careful not to
cut across the remaining perforations.
If the film
can not be trimmed without cutting across the im-
age in the frame, trim only the outer edge from the
perforation as shown above at left.
The final perforation has been cut or torn.