Nikon 9282 User Manual - Page 140

Troubleshooting

Get Nikon 9282 - Super Coolscan 4000 ED PDF manuals and user guides
UPC - 018208092826
View all Nikon 9282 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 140 highlights

Troubleshooting Should you encounter problems with your scanner, refer to the following section and the troubleshooting section in the Nikon Scan 3 Reference Manual before consulting your retailer or Nikon representative. Problem Possible Cause • The power cable is not properly connected After confirming that the scanner is off, reconnect the power 25 cable. The scanner does not turn • The scanner is off on (the status LED does not Turn the scanner on. 28 light) • The power supply to scanner has been interrupted - Try plugging a different device into the outlet used by the scanner to determine whether the problem is caused by a failed fuse or circuit breaker. • The FH-3 film holder was inserted - Turn the scanner off, remove the FH-3, and turn the scan- The status LED flashes ner on again. rapidly (scanner not • A scanner hardware malfunction has occurred - connected to computer or Turn the scanner off and disconnect it from the computer. computer off) Wait five seconds, then turn the scanner on again. If the problem persists, contact your retailer or Nikon service rep- resentative for advice. 130

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
130
Troubleshooting
Should you encounter problems with your scanner, refer to the following section and the trouble-
shooting section in the
Nikon Scan 3 Reference Manual
before consulting your retailer or Nikon
representative.
25
28
–
The scanner does not turn
on (the status LED does not
light)
• The power cable is not properly connected
After confirming that the scanner is off, reconnect the power
cable.
• The scanner is off
Turn the scanner on.
• The power supply to scanner has been interrupted
Try plugging a different device into the outlet used by the
scanner to determine whether the problem is caused by a
failed fuse or circuit breaker.
–
–
The status LED flashes
rapidly (scanner not
connected to computer or
computer off)
• The FH-3 film holder was inserted
Turn the scanner off, remove the FH-3, and turn the scan-
ner on again.
• A scanner hardware malfunction has occurred
Turn the scanner off and disconnect it from the computer.
Wait five seconds, then turn the scanner on again.
If the
problem persists, contact your retailer or Nikon service rep-
resentative for advice.
Problem
Possible Cause