Nikon S600 S600 User's Manual - Page 132

Troubleshooting, Display, Settings and Power Supply

Get Nikon S600 - Coolpix 10MP Digital Camera PDF manuals and user guides
UPC - 018208255948
View all Nikon S600 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 132 highlights

Troubleshooting If the camera fails to function as expected, check the list of common problems below before consulting your retailer or Nikon-authorized service representative. Refer to the page numbers in the right-most column for more information. Display, Settings and Power Supply Problem Cause/Solution A Monitor is blank. • Camera is off. • Battery is exhausted. • Standby mode for saving power: press the shutter-release button halfway. • When flash lamp blinks red, wait until flash has charged. • Camera and computer are connected via USB cable. • Camera and TV are connected via AV cable. 20 20 21, 25 29 63 61 Monitor is hard to read. • Adjust monitor brightness. 101 • Monitor is dirty. Clean monitor. 115 • Monitor has dimmed to save power. Monitor 15 brightens when controls are used • Use monitor brightness boost. 8 Camera turns off without warning. • Battery is low. 20 • Camera has turned off automatically to save 105 power. • Battery is cold. 114 Date and time of recording are • Pictures recorded before clock was set, and 16 not correct. "Date not set" indicator blinks during shooting, will have time stamp of "00/00/0000 00:00"; movies and voice recordings will be dated "01/01/2008 00:00." • Check camera clock regularly against more 98 accurate timepieces and reset as required. No indicators displayed in Hide info is selected for Photo info. 101 monitor. Select Show info. Date imprint not available. Camera clock has not been set. 16, 98 Date not appearing even when Date does not appear on movies. 52 Date imprint is enabled. Camera settings reset. Backup battery is exhausted; all settings were 99 restored to their default values. Technical Notes 120

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
120
Technical Notes
Troubleshooting
If the camera fails to function as expected, check the list of common problems
below before consulting your retailer or Nikon-authorized service representative.
Refer to the page numbers in the right-most column for more information.
Display, Settings and Power Supply
Problem
Cause/Solution
A
Monitor is blank.
•
Camera is off.
•
Battery is exhausted.
•
Standby mode for saving power: press the
shutter-release button halfway.
•
When flash lamp blinks red, wait until flash
has charged.
•
Camera and computer are connected via USB
cable.
•
Camera and TV are connected via AV cable.
20
20
21, 25
29
63
61
Monitor is hard to read.
•
Adjust monitor brightness.
•
Monitor is dirty. Clean monitor.
•
Monitor has dimmed to save power. Monitor
brightens when controls are used
•
Use monitor brightness boost.
101
115
15
8
Camera turns off without
warning.
•
Battery is low.
•
Camera has turned off automatically to save
power.
•
Battery is cold.
20
105
114
Date and time of recording are
not correct.
•
Pictures recorded before clock was set, and
“Date not set” indicator blinks during shooting,
will have time stamp of “00/00/0000 00:00”;
movies and voice recordings will be dated
“01/01/2008 00:00.”
•
Check camera clock regularly against more
accurate timepieces and reset as required.
16
98
No indicators displayed in
monitor.
Hide info
is selected for
Photo info
.
Select
Show info
.
101
Date imprint
not available.
Camera clock has not been set.
16, 98
Date not appearing even when
Date imprint
is enabled.
Date does not appear on movies.
52
Camera settings reset.
Backup battery is exhausted; all settings were
restored to their default values.
99