NordicTrack Cx 1055 Elliptical Exerciser English Manual - Page 8

Note: Position the Right Pedal 13 near

Page 8 highlights

8. Apply a thin film of the included Teflon® lubricant to both Pivot Shafts (15). Identify the Right Handlebar (9), which is marked with a sticker. Apply a small amount of grease to the axle on the Right Handlebar, to the Pivot Arm Cover (64), and to the Inner Upright Cover (63). Next, slide the Right Handlebar onto the right Pivot Shaft (15), and insert the axle on the Right Handlebar into the Right Upright (3). Note: Position the Right Pedal (13) near the top of the Incline Ramp (5), and then lift and push the Pedal toward the center of the Incline Ramp while inserting the axle into the Upright. Place a Wave Washer (100) on the end of the axle on the Right Handlebar (9). Next, apply a small amount of grease to an M8 x 28mm Washer (99), and slide the Washer onto an M8 x 25mm Button Screw (81). Tighten the Button Screw into the axle. Attach an Outer Upright Cover (74) to the Right Upright (3) with two M4 x 25mm Screws (105). Attach the Left Handlebar (10) to the left Pivot Shaft (15) and the Left Upright (4) in the same way. 9. Plug the Power Cord (8) into the Power Receptical (68) at the rear of the elliptical exerciser. 8 4 5 15 Lubricate 74 100 99 105 63 Axle 81 9 10 64 Grease 3 15 Lubricate 13 9 68 8 10.Make sure that all parts of the elliptical exerciser are properly tightened. Cover the floor beneath the elliptical exerciser to protect the floor from damage. Note: Some extra hardware may be left over. 8

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28

8
10.
Make sure that all parts of the elliptical exerciser are properly tightened.
Cover the floor beneath the
elliptical exerciser to protect the floor from damage. Note: Some extra hardware may be left over.
8.
Apply a thin film of the included Teflon
®
lubricant to
both Pivot Shafts (15).
Identify the Right Handlebar (9), which is marked with
a sticker. Apply a small amount of grease to the axle
on the Right Handlebar, to the Pivot Arm Cover (64),
and to the Inner Upright Cover (63). Next, slide the
Right Handlebar onto the right Pivot Shaft (15), and
insert the axle on the Right Handlebar into the Right
Upright (3).
Note: Position the Right Pedal (13) near
the top of the Incline Ramp (5), and then lift and
push the Pedal toward the center of the Incline
Ramp while inserting the axle into the Upright.
Place a Wave Washer (100) on the end of the axle on
the Right Handlebar (9). Next, apply a small amount of
grease to an M8 x 28mm Washer (99), and slide the
Washer onto an M8 x 25mm Button Screw (81).
Tighten the Button Screw into the axle.
Attach an Outer Upright Cover (74) to the Right
Upright (3) with two M4 x 25mm Screws (105).
Attach the Left Handlebar (10) to the left Pivot Shaft
(15) and the Left Upright (4) in the same way.
9
15
Lubricate
3
13
74
100
99
9.
Plug the Power Cord (8) into the Power Receptical
(68) at the rear of the elliptical exerciser.
8
68
9
8
63
64
81
105
10
5
4
Grease
15
Lubricate
Axle