NordicTrack Netl99017 Instruction Manual - Page 15

IMPORTANT: The Tablet Holder 91 is

Get NordicTrack Netl99017 PDF manuals and user guides View all NordicTrack Netl99017 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 15 highlights

17. Remove the 5/16" Nut (14) and the 5/16" x 2 1/4" Bolt (26) from the bracket on the Latch Crossbar (51). Align the upper end of the Storage Latch (52) with the bracket on the Latch Crossbar (51), and insert the 5/16" x 2 1/4" Bolt (26) through the bracket and the Storage Latch. This will push a spacer (N) out of the Storage Latch; discard the spacer. 17 14 N 51 26 54 52 Next, tighten the 5/16" Nut (14) onto the 5/16" x 2 1/4" Bolt (26). Do not overtighten the Nut; the Storage Latch (52) must be able to pivot. 86 Then, lower the Frame (54) (see HOW TO LOWER THE TREADMILL FOR USE on page 30). Press the Base Covers (85, 86) downward into place. 85 18. Press the two tabs on the Tablet Holder (91) into the slots (O) in the console assembly (G). Attach the Tablet Holder (91) with four M4 x 16mm Screws (12). Note: Start the two top Screws first, and then start the two bottom Screws. Be careful not to overtighten the Screws. IMPORTANT: The Tablet Holder (91) is designed for use with most full-size tablets. Do not place any other electronic device or object in the Tablet Holder. 18 Start First 12 91 OG 19. Make sure that all parts are properly tightened before you use the treadmill. If there are sheets of plastic on the treadmill decals, remove the plastic. To protect the floor or carpet, place a mat under the treadmill. To avoid damage to the console, keep the treadmill out of direct sunlight. Keep the included hex key in a secure place; the hex key is used to adjust the walking belt (see pages 31 and 32). Note: Extra hardware may be included. 15

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
15
51
26
54
14
52
86
85
17
17. Remove the 5/16" Nut (14) and the 5/16" x
2 1/4" Bolt (26) from the bracket on the Latch
Crossbar (51).
Align the upper end of the Storage Latch (52)
with the bracket on the Latch Crossbar (51), and
insert the 5/16" x 2 1/4" Bolt (26) through the
bracket and the Storage Latch.
This will push a
spacer (N) out of the Storage Latch; discard
the spacer.
Next, tighten the 5/16" Nut (14) onto the 5/16" x
2 1/4" Bolt (26).
Do not overtighten the Nut;
the Storage Latch (52) must be able to pivot.
Then, lower the Frame (54) (see HOW TO
LOWER THE TREADMILL FOR USE on page
30).
Press the Base Covers (85, 86) downward into
place.
N
18
91
Start First
18.
Press the two tabs on the Tablet Holder (91) into
the slots (O) in the console assembly (G).
Attach the Tablet Holder (91) with four M4 x
16mm Screws (12).
Note: Start the two top
Screws
fi
rst, and then start the two bottom
Screws. Be careful not to overtighten the
Screws.
IMPORTANT: The Tablet Holder (91) is
designed for use with most full-size tablets.
Do not place any other electronic device or
object in the Tablet Holder.
G
O
12
19.
Make sure that all parts are properly tightened before you use the treadmill.
If there are sheets of plastic
on the treadmill decals, remove the plastic. To protect the floor or carpet, place a mat under the treadmill. To
avoid damage to the console, keep the treadmill out of direct sunlight. Keep the included hex key in a secure
place; the hex key is used to adjust the walking belt (see pages 31 and 32). Note: Extra hardware may be
included.