Olympus IR 300 IR-300 Advanced Manual (English) - Page 148

Set [ALL RESET] to [OFF].

Get Olympus IR 300 - Digital Camera - 5.0 Megapixel PDF manuals and user guides
UPC - 050332151352
View all Olympus IR 300 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 148 highlights

Troubleshooting Possible cause Corrective action Ref. page The monitor is hard to see. There is condensation* inside the camera. The brightness of the monitor is not adjusted properly. Turn the camera off and wait until it dries before turning it on again. Use [s] to adjust the brightness. - P. 100 The monitor is exposed Block the sunlight with your hand. - to direct sunlight. Vertical lines appear on Aiming the camera at a bright subject in - the monitor screen sunlight may cause vertical lines to appear during shooting. on the screen. This is not a malfunction. The date recorded with the image data is wrong. The date/time is not set. Set the date and time. The clock adjustment P. 101 is not factory-preset. The camera has been left without the battery. If the camera is left without the battery for 1 day, the date/time setting is canceled. Set the date/time again. P. 101 The settings are returned to the factory default settings when the camera is turned off. [ALL RESET] is set to [ON]. Set [ALL RESET] to [OFF]. P. 93 The picture is out of focus. The subject was too close. Move further away from the subject. To take pictures closer than 10 cm (3.9") with the zoom in the maximum wide position, use the super macro mode. P. 37 Auto focus is not possible. Use the focus lock to focus on the subject. P. 22 There is condensation* Turn the camera off and wait until it dries - inside the camera. before turning it on again. The monitor goes off. The camera is in the Operate the camera with the shutter button or - sleep mode. zoom lever. Appendix 12 148

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
  • 171
  • 172
  • 173
  • 174
  • 175
  • 176
  • 177
  • 178
  • 179
  • 180
  • 181
  • 182
Troubleshooting
148
12
Appendix
The monitor is hard to see.
There is condensation*
inside the camera.
Turn the camera off and wait until it dries
before turning it on again.
–
The brightness of the
monitor is not adjusted
properly.
Use [
s
] to adjust the brightness.
P. 100
The monitor is exposed
to direct sunlight.
Block the sunlight with your hand.
–
Vertical lines appear on
the monitor screen
during shooting.
Aiming the camera at a bright subject in
sunlight may cause vertical lines to appear
on the screen. This is not a malfunction.
–
The date recorded with the image data is wrong.
The date/time is not set.
Set the date and time. The clock adjustment
is not factory-preset.
P. 101
The camera has been
left without the battery.
If the camera is left without the battery for
1 day, the date/time setting is canceled. Set
the date/time again.
P. 101
The settings are returned to the factory default settings when the camera is turned off.
[ALL RESET] is set to
[ON].
Set [ALL RESET] to [OFF].
P. 93
The picture is out of focus.
The subject was too
close.
Move further away from the subject. To take
pictures closer than 10 cm (3.9") with the
zoom in the maximum wide position, use the
super macro mode.
P. 37
Auto focus is not
possible.
Use the focus lock to focus on the subject.
P. 22
There is condensation*
inside the camera.
Turn the camera off and wait until it dries
before turning it on again.
–
The monitor goes off.
The camera is in the
sleep mode.
Operate the camera with the shutter button or
zoom lever.
–
Possible cause
Corrective action
Ref.
page