Onkyo AVX-290 Owner Manual - Page 18

Playback, Playing the Connected Component, Listening to AM/FM Radio

Get Onkyo AVX-290 PDF manuals and user guides View all Onkyo AVX-290 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 18 highlights

Playback The on-screen menus appear only on a TV that is connected to the HDMI OUT. If your TV is connected to the MONITOR OUT V or the COMPONENT VIDEO OUT, use the AV receiver's display when changing settings. This manual describes the procedure using the remote controller unless otherwise specified. Playing the Connected Component ■ Operating with the remote controller 1 Press RECEIVER followed by INPUT SELECTOR. 2 Start playback on the source component. See also: • "Listening to AM/FM Radio" (➔ page 18) • "iPod/iPhone Playback via Onkyo Dock" (➔ page 38) • "Controlling Other Onkyo Components" (➔ page 41) 3 To adjust the volume, use VOL R/X. 4 Select a listening mode and enjoy! See also: • "Using the Listening Modes" (➔ page 21) ■ Operating on the AV receiver 1 Use the input selector buttons to select the input source. 2 Start playback on the source component. 3 To adjust the volume, use the MASTER VOLUME control. 4 Select a listening mode and enjoy! Listening to AM/FM Radio This section describes the procedure using the buttons on the front panel unless otherwise specified. Using the Tuner With the built-in tuner you can enjoy AM and FM radio stations. You can store your favorite stations as presets for quick selection. You can change the frequency steps (➔ page 34). 1 Press TUNER to select either "AM" or "FM". In this example, FM has been selected. Each time you press TUNER, the radio band changes between AM and FM. Band Frequency (Actual display depends on the country.) Tuning into Radio Stations ■ Auto tuning mode 1 Press TUNING MODE so that the AUTO indicator lights on the display. 2 Press TUNING R/X. Searching stops when a station is found. When tuned into a station, the TUNED indicator lights. When tuned into a stereo FM station, the FM STEREO indicator lights on the display, as shown. FM STEREO AUTO TUNED Tip • Tuning into weak FM stereo stations If the signal from a stereo FM station is weak, it may be impossible to get good reception. In this case, switch to manual tuning mode and listen to the station in mono. • Alternatively, you can use the remote controller's TUN MODE and arrow buttons. En 18

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
18
En
Playback
■
Operating with the remote controller
■
Operating on the AV receiver
Using the Tuner
With the built-in tuner you can enjoy AM and FM radio
stations. You can store your favorite stations as presets for
quick selection.
You can change the frequency steps (
➔
page 34
).
Tuning into Radio Stations
■
Auto tuning mode
The on-screen menus appear only on a TV that is
connected to the
HDMI OUT
. If your TV is connected
to the
MONITOR OUT V
or the
COMPONENT
VIDEO OUT
, use the AV receiver’s display when
changing settings.
This manual describes the procedure using the
remote controller unless otherwise specified.
Playing the Connected Component
1
Press
RECEIVER
followed by
INPUT
SELECTOR
.
2
Start playback on the source component.
See also:
• “Listening to AM/FM Radio” (
➔
page 18
)
• “iPod/iPhone Playback via Onkyo Dock”
(
➔
page 38
)
• “Controlling Other Onkyo Components”
(
➔
page 41
)
3
To adjust the volume, use
VOL
q
/
w
.
4
Select a listening mode and enjoy!
See also:
• “Using the Listening Modes” (
➔
page 21
)
1
Use the input selector buttons to select the input
source.
2
Start playback on the source component.
3
To adjust the volume, use the
MASTER VOLUME
control.
4
Select a listening mode and enjoy!
Listening to AM/FM Radio
This section describes the procedure using the
buttons on the front panel unless otherwise specified.
1
Press
TUNER
to select either “AM” or “FM”.
In this example, FM has been selected.
Each time you press
TUNER
, the radio band changes
between AM and FM.
(Actual display depends on the country.)
1
Press
TUNING MODE
so that the AUTO indicator
lights on the display.
2
Press
TUNING
q
/
w
.
Searching stops when a station is found.
When tuned into a station, the
TUNED
indicator
lights. When tuned into a stereo FM station, the
FM
STEREO
indicator lights on the display, as shown.
Tip
•
Tuning into weak FM stereo stations
If the signal from a stereo FM station is weak, it may be
impossible to get good reception. In this case, switch to
manual tuning mode and listen to the station in mono.
•
Alternatively, you can use the remote controller’s
TUN
MODE
and arrow buttons.
Band
Frequency
FM STEREO
AUTO
TUNED