Onkyo HT-S3200 B User Manual - Page 41

Using the Music Optimizer, Specifying the Digital Signal Format, To turn the Music Optimizer

Get Onkyo HT-S3200 B PDF manuals and user guides View all Onkyo HT-S3200 B manuals
Add to My Manuals
Save this manual to your list of manuals

Page 41 highlights

Basic Operations-Continued Using the Music Optimizer The Music Optimizer function enhances the sound quality of compressed music files. Use it with music files that use "lossy" compression, such as MP3. To turn the Music Optimizer "On" or "Off", use the AV receiver's [MUSIC OPTIMIZER] button. Off: Music Optimizer off (default). On: Music Optimizer on. Tip: This procedure can also be performed on the remote controller by using [AUDIO] button (see page 60). Note: The Music Optimizer function only works with PCM digital audio input signals with a sampling rate below 48 kHz and analog audio input signals. The Music Optimizer is disabled when the Direct listening mode is selected. Specifying the Digital Signal Format The following table shows the display indicator for each digital signal format. Format Dolby Digital DTS PCM Display PCM Normally, the AV receiver detects the format of digital input signals automatically. However, if you experience either of the following issues when playing PCM or DTS sources, you can specify the signal format manually. • If the beginnings of tracks from a PCM source are cut off, try the PCM setting. • If noise is produced when fast forwarding or rewinding a DTS CD, try the DTS setting. F, S AUDIO 1 Press and hold [AUDIO] button for about 8 seconds. 2 While "Auto" is displayed (about 3 seconds), use the Left and Right [F]/[S] buttons to select: PCM, DTS, or Auto. PCM: Only 2-channel PCM format input signals will be heard. If the input signal is not PCM, the PCM indicator will flash and there will be no sound. DTS: Only DTS format input signals will be heard. If the input signal is not DTS, the DTS indicator will flash and there will be no sound. Auto (default): The format is detected automatically. If no digital input signal is present, the corresponding analog input is used instead. 41

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
41
Basic Operations
—Continued
The Music Optimizer function enhances the sound
quality of compressed music files. Use it with music files
that use “lossy” compression, such as MP3.
Note:
The Music Optimizer function only works with PCM
digital audio input signals with a sampling rate below
48 kHz and analog audio input signals. The Music Opti-
mizer is disabled when the Direct listening mode is
selected.
The following table shows the display indicator for each
digital signal format.
Normally, the AV receiver detects the format of digital
input signals automatically. However, if you experience
either of the following issues when playing PCM or DTS
sources, you can specify the signal format manually.
•
If the beginnings of tracks from a PCM source are cut
off, try the PCM setting.
•
If noise is produced when fast forwarding or
rewinding a DTS CD, try the DTS setting.
Using the Music Optimizer
To turn the Music Optimizer “On”
or “Off”, use the AV receiver’s
[MUSIC OPTIMIZER] button.
Tip:
This procedure can also be performed
on the remote controller by using
[AUDIO] button (see page 60).
Off:
Music Optimizer off (default).
On:
Music Optimizer on.
Specifying the Digital Signal Format
Format
Display
Dolby Digital
DTS
PCM
1
Press and hold [AUDIO] button
for about 8 seconds.
2
While “Auto” is displayed (about
3 seconds), use the Left and
Right [
e
]/[
r
] buttons to select:
PCM, DTS, or Auto.
PCM:
Only 2-channel PCM format input
signals will be heard. If the input
signal is not PCM, the PCM
indicator will flash and there will be
no sound.
DTS:
Only DTS format input signals will
be heard. If the input signal is not
DTS, the DTS indicator will flash
and there will be no sound.
Auto (default):
The format is detected
automatically. If no digital input
signal is present, the corresponding
analog input is used instead.
PCM
AUDIO
e
,
r