Onkyo HT-S7100 Owner Manual - Page 41

Changing the Speaker Settings Manually, Using a Powered Subwoofer

Get Onkyo HT-S7100 PDF manuals and user guides
UPC - 751398008559
View all Onkyo HT-S7100 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 41 highlights

First Time Setup-Continued Auto Speaker Setup AUDYSSEY - - - - - Speaker Detect Error - - - - - FL : Yes SL : --SBL : No C : Yes FR : Yes SR : Yes SBR : Yes SW : --- Retry Cancel The right surround back speaker has been detected but the left surround back speaker hasn't. Auto Speaker Setup AUDYSSEY - - - - - Speaker Detect Error - - - - - FL : Error SL : Yes SBL : Yes C : Yes FR : Yes SR : Yes SBR : Yes SW : Yes Retry Cancel There is a problem with a speaker. The speaker may be broken or the subwoofer may be emitting sound that is too high. Auto Speaker Setup AUDYSSEY Speaker Detect Error Retry Cancel The number of speakers detected on the second or third measurement was different to the number detected on the first measurement. Make sure speakers that cannot be detected are connected properly. Retry: Return to step 2 and try again. Cancel: Cancel the automatic speaker setup. ❏ Write Error Auto Speaker Setup AUDYSSEY To Retry the Automatic Speaker Setup Press the [ENTER] button. Make sure speakers that cannot be detected are connected properly. Changing the Speaker Settings Manually If you wish to make changes to the settings found during the automatic speaker setup, follow the directions on pages 72-76. Using a Powered Subwoofer If you're using a powered subwoofer and it outputs very low-frequency sound at a low volume level, it may not be detected by the automatic speaker setup. If the subwoofer (SW) appears on the "SP Detect Result" screen as "No", increase the subwoofer's volume to the halfway point, set it to its highest crossover frequency, and then try running the automatic speaker setup again. Note that if the volume is set too high and the sound distorts, detection issues may occur, so use an appropriate volume level. Writing Error! Retry Cancel This message appears if saving fails. Try saving again. If this message appears after 2 or 3 attempts, the AV receiver is probably malfunctioning. Contact your Onkyo dealer. Retry: Return to step 2 and try again. Cancel: Cancel the automatic speaker setup. 41

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
41
First Time Setup
—Continued
The right surround back speaker has been detected
but the left surround back speaker hasn’t.
There is a problem with a speaker. The speaker may
be broken or the subwoofer may be emitting sound
that is too high.
The number of speakers detected on the second or
third measurement was different to the number
detected on the first measurement.
Make sure speakers that cannot be detected are con-
nected properly.
Retry
: Return to step 2 and try again.
Cancel
: Cancel the automatic speaker setup.
❏
Write Error
This message appears if saving fails.
Try saving again. If this message appears after 2 or 3
attempts, the AV receiver is probably malfunctioning.
Contact your Onkyo dealer.
Retry
: Return to step 2 and try again.
Cancel
: Cancel the automatic speaker setup.
Changing the Speaker Settings Manually
If you wish to make changes to the settings found during
the automatic speaker setup, follow the directions on
pages 72–76.
Using a Powered Subwoofer
If you’re using a powered subwoofer and it outputs very
low-frequency sound at a low volume level, it may not be
detected by the automatic speaker setup. If the sub-
woofer (SW) appears on the “SP Detect Result” screen
as “No”, increase the subwoofer’s volume to the half-
way point, set it to its highest crossover frequency, and
then try running the automatic speaker setup again. Note
that if the volume is set too high and the sound distorts,
detection issues may occur, so use an appropriate
volume level.
Auto Speaker Setup
- - - - - Speaker Detect Error - - - - -
AUDYSSEY
Cancel
Retry
:
Yes
:
---
:
:
Yes
No
:
Yes
:
Yes
:
Yes
:
---
FL
SL
SBL
C
FR
SR
SBR
SW
Auto Speaker Setup
- - - - - Speaker Detect Error - - - - -
AUDYSSEY
Cancel
Retry
:
Error
:
Yes
:
Yes
:
Yes
:
Yes
:
Yes
:
Yes
:
Yes
FL
SL
SBL
C
FR
SR
SBR
SW
Auto Speaker Setup
Speaker Detect Error
AUDYSSEY
Cancel
Retry
Auto Speaker Setup
Writing Error!
AUDYSSEY
Cancel
Retry
To Retry the Automatic Speaker Setup
Press the [ENTER] button.
Make sure speakers that cannot be
detected are connected properly.