Onkyo TX-NR1008 Owner Manual - Page 60

Lock Setup, Using the Audio Settings, Tone Control Settings, Speaker Levels

Get Onkyo TX-NR1008 PDF manuals and user guides View all Onkyo TX-NR1008 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 60 highlights

■ Universal Port ` via NET: You can update the firmware via Internet. Check the network connection before update. ` via USB: You can update the firmware from a USB mass storage device. You can update the Onkyo dock's firmware. Do not shutdown the power of the AV receiver while update. Note • This update shall not be performed when no dock is connected to UNIVERSAL PORT jack. Lock Setup With this preference, you can protect your settings by locking the setup menus. Main menu Lock Setup ■ Setup ` Locked: Setup menus locked. ` Unlocked: Setup menus not locked. When the setup menus are locked, you cannot change any setting. Using the Audio Settings You can change various audio settings from the Home menu (➔ 27). 1 Press RECEIVER followed by HOME. 2 UseR/X to select "Audio", and then use R/X/F/S to make the desired selection. Note • These settings are disabled when: - a pair of headphones is connected, or - the "Audio TV Out" setting is set to "On" (➔ 58) and an input selector other than HDMI is selected. Tone Control Settings You can adjust the bass and treble for the front speakers, except when the Direct, Pure Audio or THX listening mode is selected. ■ Bass ` -10dB to 0dB to +10dB in 2 dB steps. You can boost or cut low-frequency sounds output by the front speakers. ■ Treble ` -10dB to 0dB to +10dB in 2 dB steps. You can boost or cut high-frequency sounds output by the front speakers. Operating on the AV receiver 1 Press TONE on the AV receiver repeatedly to select either "Bass" or "Treble". 2 Use Up S and Down F on the AV receiver to adjust. Note • This setting is not available when the multichannel analog input is selected. Speaker Levels You can adjust the volume of each speaker while listening to an input source. These temporary adjustments are cancelled when the AV receiver is set to Standby. To save the setting you made here, go to "Level Calibration" (➔ 48) before setting the AV receiver to Standby. ■ Subwoofer Level ` -15.0dB to 0.0dB to +12.0dB in 1 dB steps. ■ Center Level ` -12.0dB to 0.0dB to +12.0dB in 1 dB steps. Note • You cannot use this function while the AV receiver is muted. • Speakers that are set to "No" or "None" in the "Speaker Configuration" (➔ 47) cannot be adjusted. En 60

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
60
En
■
Universal Port
via NET
:
You can update the firmware via Internet. Check the
network connection before update.
via USB
:
You can update the firmware from a USB mass stor-
age device.
You can update the Onkyo dock’s firmware. Do not shut-
down the power of the AV receiver while update.
Note
•
This update shall not be performed when no dock is connected
to
UNIVERSAL PORT
jack.
With this preference, you can protect your settings by
locking the setup menus.
Main menu
Lock Setup
■
Setup
Locked
:
Setup menus locked.
Unlocked
:
Setup menus not locked.
When the setup menus are locked, you cannot change any
setting.
You can change various audio settings from the Home
menu (
➔
27
).
Note
•
These settings are disabled when:
– a pair of headphones is connected, or
– the “
Audio TV Out
” setting is set to “
On
” (
➔
58
) and an
input selector other than
HDMI
is selected.
Tone Control Settings
You can adjust the bass and treble for the front speakers,
except when the Direct, Pure Audio or THX listening
mode is selected.
■
Bass
–10dB
to
0dB
to
+10dB
in 2 dB steps.
You can boost or cut low-frequency sounds output
by the front speakers.
■
Treble
–10dB
to
0dB
to
+10dB
in 2 dB steps.
You can boost or cut high-frequency sounds output
by the front speakers.
Operating on the AV receiver
Note
•
This setting is not available when the multichannel analog input
is selected.
Speaker Levels
You can adjust the volume of each speaker while listening
to an input source.
These temporary adjustments are cancelled when the AV
receiver is set to Standby. To save the setting you made
here, go to “Level Calibration” (
➔
48
) before setting the
AV receiver to Standby.
■
Subwoofer Level
–15.0dB
to
0.0dB
to
+12.0dB
in 1 dB steps.
■
Center Level
–12.0dB
to
0.0dB
to
+12.0dB
in 1 dB steps.
Note
•
You cannot use this function while the AV receiver is muted.
•
Speakers that are set to “
No
” or “
None
” in the
“Speaker Configuration” (
➔
47
) cannot be adjusted.
Lock Setup
Using the Audio Settings
1
Press
RECEIVER
followed by
HOME
.
2
Use
q
/
w
to select “Audio”, and then use
q
/
w
/
e
/
r
to make the desired selection.
1
Press
TONE
on the AV receiver repeatedly to
select either “Bass” or “Treble”.
2
Use Up
r
and Down
e
on the AV receiver to
adjust.