Onkyo TX-NR1010 Owner Manual - Page 87

Using a Multiroom Kit with a Cabinet, Components, En-87

Get Onkyo TX-NR1010 PDF manuals and user guides View all Onkyo TX-NR1010 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 87 highlights

From the connecting block Miniplug cable AV receiver Signal flow Using a Multiroom Kit with a Cabinet In this setup, the IR receiver picks up the infrared signals from the remote controller and feeds them to the AV receiver located in the cabinet via the connecting block. IR IN Connecting block IR receiver Inside cabinet Signal flow Remote controller Using a Multiroom Kit with Other Components In this setup, an IR emitter is connected to the AV receiver's IR OUT jack and placed in front of the other component's remote control sensor. Infrared signals received at the AV receiver's IR IN jack are fed through to the other component via the IR emitter. Signals picked up by the AV receiver's remote control sensor are not output. IR IN IR OUT Connecting block AV receiver IR Emitter IR receiver Remote controller Other component Signal flow The IR emitter should be connected to the AV receiver's IR OUT jack, as shown below. From the connecting block Miniplug cable Other component Remote control sensor AV receiver Emitter IR Emitter Miniplug Signal flow En-87 Advanced Operations

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
Advanced Operations
En-87
Using a Multiroom Kit with a Cabinet
In this setup, the IR receiver picks up the infrared signals
from the remote controller and feeds them to the AV
receiver located in the cabinet via the connecting block.
Using a Multiroom Kit with Other
Components
In this setup, an IR emitter is connected to the AV
receiver’s
IR OUT
jack and placed in front of the other
component’s remote control sensor. Infrared signals
received at the AV receiver’s
IR IN
jack are fed through to
the other component via the IR emitter. Signals picked up
by the AV receiver’s remote control sensor are not output.
The IR emitter should be connected to the AV receiver’s
IR OUT
jack, as shown below.
From the connecting block
Miniplug cable
AV receiver
Signal flow
IR IN
Connecting
block
Remote controller
IR
receiver
Inside
cabinet
Signal flow
IR IN
IR OUT
Connecting
block
IR receiver
Remote controller
Signal flow
IR Emitter
Other component
AV receiver
Remote control sensor
Other component
Emitter
Signal flow
Miniplug
Miniplug cable
AV receiver
From the connecting block
IR Emitter