Onkyo TX-NR717 Owner Manual - Page 32

En-32, Tuning into Radio Stations, Presetting AM/FM Stations

Get Onkyo TX-NR717 PDF manuals and user guides View all Onkyo TX-NR717 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 32 highlights

Tuning into Radio Stations ■ Auto tuning mode 1 Press TUNING MODE so that the AUTO indicator lights on the AV receiver's display. 2 Press TUNING R/X. Searching stops when a station is found. When tuned into a station, the TUNED indicator lights. When tuned into a stereo FM station, the FM STEREO indicator lights as shown. TUNED AUTO FM STEREO Tip • Tuning into weak FM stereo stations If the signal from a stereo FM station is weak, it may be impossible to get good reception. In this case, switch to manual tuning mode and listen to the station in mono. ■ Manual tuning mode In manual tuning mode, FM stations will be in mono. 1 Press TUNING MODE so that the AUTO indicator goes off on the AV receiver's display. 2 Press and hold TUNING R/X. The frequency stops changing when you release the button. Press the buttons repeatedly to change the frequency one step at a time. ■ Tuning into stations by frequency You can tune into AM and FM stations directly by entering the appropriate frequency. 1 On the remote controller, press TUNER repeatedly to select "AM" or "FM", followed by D.TUN. (Actual display depends on the country.) 2 Within 8 seconds, use the number buttons to enter the frequency of the radio station. For example, to tune to 87.5 (FM), press 8, 7, 5 or 8, 7, 5, 0. If you have entered the wrong number, you can retry after 8 seconds. Presetting AM/FM Stations You can store a combination of up to 40 of your favorite AM/FM radio stations as presets. 1 Tune into the AM/FM station that you want to store as a preset. See the previous section. 2 Press MEMORY. The preset number flashes. (Actual display depends on the country.) 3 While the preset number is flashing (about 8 seconds), use PRESET F/S to select a preset from 1 through 40. Turning On & Basic Operations 4 Press MEMORY again to store the station or channel. The station or channel is stored and the preset number stops flashing. Repeat this procedure for all of your favorite AM/FM radio stations. ■ Selecting Presets 1 To select a preset, use PRESET F/S on the AV receiver, or the remote controller's CH +/-. Tip • You can also use the remote controller's number buttons to select a preset directly. ■ Deleting Presets 1 Select the preset that you want to delete. See the previous section. 2 While holding down MEMORY, press TUNING MODE. The preset is deleted and its number disappears from the AV receiver's display. En-32

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
Turning On & Basic Operations
En-32
Tuning into Radio Stations
■
Auto tuning mode
■
Manual tuning mode
In manual tuning mode, FM stations will be in mono.
■
Tuning into stations by frequency
You can tune into AM and FM stations directly by entering
the appropriate frequency.
Presetting AM/FM Stations
You can store a combination of up to 40 of your favorite
AM/FM radio stations as presets.
■
Selecting Presets
■
Deleting Presets
1
Press
TUNING MODE
so that the AUTO indicator
lights on the AV receiver’s display.
2
Press
TUNING
q
/
w
.
Searching stops when a station is found.
When tuned into a station, the
TUNED
indicator
lights. When tuned into a stereo FM station, the
FM
STEREO
indicator lights as shown.
Tip
•
Tuning into weak FM stereo stations
If the signal from a stereo FM station is weak, it may be
impossible to get good reception. In this case, switch to
manual tuning mode and listen to the station in mono.
1
Press
TUNING MODE
so that the AUTO indicator
goes off on the AV receiver’s display.
2
Press and hold
TUNING
q
/
w
.
The frequency stops changing when you release the
button.
Press the buttons repeatedly to change the frequency
one step at a time.
TUNED
FM STEREO
AUTO
1
On the remote controller, press
TUNER
repeatedly
to select “AM” or “FM”, followed by
D.TUN
.
(Actual display depends on the country.)
2
Within 8 seconds, use the number buttons to enter
the frequency of the radio station.
For example, to tune to 87.5 (FM), press
8
,
7
,
5
or
8
,
7
,
5
,
0
.
If you have entered the wrong number, you can retry
after 8 seconds.
1
Tune into the AM/FM station that you want to store
as a preset.
See the previous section.
2
Press
MEMORY
.
The preset number flashes.
(Actual display depends on the country.)
3
While the preset number is flashing (about 8
seconds), use
PRESET
e
/
r
to select a preset from
1 through 40.
4
Press
MEMORY
again to store the station or
channel.
The station or channel is stored and the preset number
stops flashing.
Repeat this procedure for all of your favorite AM/FM
radio stations.
1
To select a preset, use
PRESET
e
/
r
on the AV
receiver, or the remote controller’s
CH +/–
.
Tip
•
You can also use the remote controller’s number buttons to
select a preset directly.
1
Select the preset that you want to delete.
See the previous section.
2
While holding down
MEMORY
, press
TUNING
MODE
.
The preset is deleted and its number disappears from
the AV receiver’s display.