Onkyo TX-NR717 Owner Manual - Page 82

■ About DTS signals When DTS program material ends and the DTS - bitstream stops, the AV receiver remains in DTS listening mode and the dts indicator remains on. This is to prevent noise when you use the pause, fast forward, or fast reverse function on your player. If you switch your player from DTS to PCM, you may not hear any sound because the AV receiver does not switch formats immediately. In such case, you should stop your player for about three seconds and then resume playback. With some CD and LD players, you won't be able to - playback DTS material properly even though your player is connected to a digital input on the AV receiver. This is usually because the DTS bitstream has been processed (e.g., output level, sampling rate, or frequency response changed) and the AV receiver doesn't recognize it as a genuine DTS signal. In such cases, you may hear noise. Playing DTS program material, using the pause, fast - forward, or fast reverse function on your player may produce a short audible noise. This is not a malfunction. ■ The beginning of audio received by an HDMI IN can't be heard Since it takes longer to identify the format of an - HDMI signal than it does for other digital audio signals, audio output may not start immediately. ■ There's no sound during Whole House Mode Make sure you've selected an analog audio input. 54 Video ■ There's no picture Make sure that all video connecting plugs are pushed 15 in all the way. Make sure that each video component is properly connected. 16, 17 If your TV is connected to the HDMI output, select 53 in the "HDMI Input" setting to watch composite video, and component video sources. If the video source is connected to a component video 17, 54 input, you must assign that input to an input selector, and your TV must be connected to either the HDMI output or COMPONENT VIDEO OUT. If the video source is connected to a composite video 17 input, your TV must be connected to the HDMI output or the corresponding composite video output. If the video source is connected to an HDMI input, you must assign that input to an input selector, and your TV must be connected to the HDMI output. 16, 53 While the Pure Audio listening mode is selected, the 38 video circuitry is turned off and only video signals input through HDMI IN can be output. On your TV, make sure that the video input to which - the AV receiver is connected is selected. ■ There's no picture from a source connected to an HDMI IN Reliable operation with an HDMI-to-DVI adapter is 95 not guaranteed. In addition, video signals from a PC are not guaranteed. When the resolution is set to any resolution not 53 supported by the TV, no video is output from the HDMI output. If the message "Resolution Error" appears on the - AV receiver's display, this indicates that your TV does not support the current video resolution and you need to select another resolution on your DVD player. ■ The on-screen menus don't appear On your TV, make sure that the video input to which - the AV receiver is connected is selected. When the AV receiver is not connected to a TV via - HDMI OUT MAIN, on-screen menus are not displayed. Appendix ■ The on-screen information does not appear Depending on the input signal, the on screen 48 information may not appear when the input signal from HDMI IN is output to a device connected to the HDMI output. Tuner ■ Reception is noisy, FM stereo reception is noisy, or the FM STEREO indicator doesn't light Relocate your antenna. - Move the AV receiver away from your TV or - computer. Listen to the station in mono. 32 When listening to an AM station, operating the - remote controller may cause noise. Passing cars and airplanes can cause interference. - Concrete walls weaken radio signals. - If nothing improves the reception, install an outdoor - antenna. Remote Controller ■ The remote controller doesn't work Before operating this unit, be sure to press - RECEIVER. Make sure that the batteries are installed with the 5 correct polarity. Install new batteries. Don't mix different types of 5 batteries, or old and new batteries. Make sure that the remote controller is not too far 5 away from the AV receiver, and that there's no obstruction between the remote controller and the AV receiver's remote control sensor. Make sure that the AV receiver is not subjected to - direct sunshine or inverter-type fluorescent lights. Relocate if necessary. If the AV receiver is installed in a rack or cabinet - with colored-glass doors, the remote controller may not work reliably when the doors are closed. En-82