Onkyo TX-NR717 Owner Manual - Page 71

Controlling Multi Zone Components, En-71

Get Onkyo TX-NR717 PDF manuals and user guides View all Onkyo TX-NR717 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 71 highlights

Note • The volume of Zone 2/3 must be set on the Zone 2/3 amplifier. Zone 2 12V Trigger When Zone 2 is turned on, the output from the ZONE 2 12V TRIGGER OUT jack goes high (+12 V and max. 150 mA for Zone 2). Connecting this jack to a 12-volt trigger input on a component in Zone 2 will make that component turn on or off as the AV receiver turns on or off the Zone 2. Controlling Multi Zone Components ■ Operating on the AV receiver Input selector buttons ZONE 2 ZONE 3 MASTER VOLUME 1 To turn on Zone 2/3 and select an input source, press ZONE 2 or ZONE 3 followed by an input selector button within 8 seconds. Zone 2/3 turns on, the Z2 or Z3 indicator lights on the AV receiver's display. Tip • The Zone 2 trigger output goes high (+12 V). To select the same source as the main room's, press ZONE 2 or ZONE 3 twice. "Zone 2 Selector: Source" or "Zone 3 Selector: Source" appears on the AV receiver's display. 2 To turn off Zone 2/3, press ZONE 2 or ZONE 3 followed by ON/STANDBY within 8 seconds. The zone is turned off. Tip • The Zone 2 trigger output goes low (0 volts). ■ Operating on the remote controller To control Zone 2/3, you must press ZONE2 or ZONE3 on the remote controller first. ON/STANDBY Tip • The Whole House Mode function shares the input source of main room with Multi Zone (➔ page 47). RECEIVER ZONE2 ZONE3 INPUT SELECTOR MUTING VOLR/X Advanced Operations 1 Press ZONE2 or ZONE3, then point the remote controller at the AV receiver and press RECEIVER. Zone 2/3 turns on, the Z2 or Z3 indicator lights on the AV receiver's display. Tip • The Zone 2 trigger output goes high (+12 V). 2 To select an input source for Zone 2/3, press ZONE2 or ZONE3, followed by an INPUT SELECTOR button. 3 To turn off Zone 2/3, press ZONE2 or ZONE3, followed by RECEIVER. The zone is turned off. Tip • The Zone 2 trigger output goes low (0 volts). Adjusting the Volume for Zones ■ Operating on the remote controller 1 Press ZONE2 or ZONE3. 2 Use VOL R/X. ■ Operating on the AV receiver 1 Press ZONE 2 or ZONE 3 (the Z2/Z3 indicator on the display flashes). 2 Use MASTER VOLUME control within 8 seconds. If your Zone 2/3 speakers are connected to a receiver or integrated amplifier in Zone 2/3, use its volume control to adjust the volume. En-71

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
Advanced Operations
En-71
Note
•
The volume of Zone 2/3 must be set on the Zone 2/3 amplifier.
Zone 2 12V Trigger
When Zone 2 is turned on, the output from the
ZONE 2
12V TRIGGER OUT
jack goes high (+12 V and max. 150
mA for Zone 2). Connecting this jack to a 12-volt trigger
input on a component in Zone 2 will make that component
turn on or off as the AV receiver turns on or off the Zone 2.
■
Operating on the AV receiver
Tip
•
The Whole House Mode function shares the input source of main
room with Multi Zone (
➔
page 47
).
■
Operating on the remote controller
To control Zone 2/3, you must press
ZONE2
or
ZONE3
on the remote controller first.
Adjusting the Volume for Zones
■
Operating on the remote controller
■
Operating on the AV receiver
If your Zone 2/3 speakers are connected to a receiver or
integrated amplifier in Zone 2/3, use its volume control to
adjust the volume.
Controlling Multi Zone Components
ZONE 2
ZONE 3
MASTER VOLUME
8
ON/STANDBY
Input selector buttons
1
To turn on Zone 2/3 and select an input source,
press
ZONE 2
or
ZONE 3
followed by an input
selector button within 8 seconds.
Zone 2/3 turns on, the
Z2
or
Z3
indicator lights on the
AV receiver’s display.
Tip
•
The Zone 2 trigger output goes high (+12 V).
To select the same source as the main room’s, press
ZONE 2
or
ZONE 3
twice. “
Zone 2 Selector:
Source
” or “
Zone 3 Selector: Source
” appears on the
AV receiver’s display.
2
To turn off Zone 2/3, press
ZONE 2
or
ZONE 3
followed by
8
ON/STANDBY
within 8 seconds.
The zone is turned off.
Tip
•
The Zone 2 trigger output goes low (0 volts).
8
RECEIVER
ZONE2
ZONE3
INPUT
SELECTOR
VOL
q
/
w
MUTING
1
Press
ZONE2
or
ZONE3
, then point the remote
controller at the AV receiver and press
8
RECEIVER
.
Zone 2/3 turns on, the
Z2
or
Z3
indicator lights on the
AV receiver’s display.
Tip
•
The Zone 2 trigger output goes high (+12 V).
2
To select an input source for Zone 2/3, press
ZONE2
or
ZONE3
, followed by an
INPUT
SELECTOR
button.
3
To turn off Zone 2/3, press
ZONE2
or
ZONE3
,
followed by
8
RECEIVER
.
The zone is turned off.
Tip
•
The Zone 2 trigger output goes low (0 volts).
1
Press
ZONE2
or
ZONE3
.
2
Use
VOL
q
/
w
.
1
Press
ZONE 2
or
ZONE 3
(the Z2/Z3 indicator on
the display flashes).
2
Use
MASTER VOLUME
control within 8 seconds.