Onkyo TX-NR828 Owner's Manual English - Page 83

Remapping Colored Buttons, Remote Control Codes for Onkyo Components Connected via RI

Get Onkyo TX-NR828 PDF manuals and user guides View all Onkyo TX-NR828 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 83 highlights

3 Within 30 seconds, use the number buttons to enter the 5-digit remote control code. The REMOTE MODE button flashes twice. If the remote control code is not entered successfully, the REMOTE MODE button will flash once slowly. Note • Though the provided remote control codes are correct at the time of release, they are subject to change. Remapping Colored Buttons You can change the configuration of colored buttons, with which REMOTE MODE buttons are preset. 1 While holding down the REMOTE MODE button that you want to program, press and hold down A (Red) until the REMOTE MODE button lights (about 3 seconds). You can only change colored buttons for components whose codes belong to categories of the Remote Control Codes list (BD/DVD player, TV, cable set-top box, etc). 2 Within 30 seconds, press the colored buttons in the order that you want to reassign them. The button presses are assigned to each button from left to right. The REMOTE MODE button flashes twice, indicating that the sequence has been successfully assigned. If the sequence is not successfully assigned, the REMOTE MODE button will flash once slowly. Tip • To reset the REMOTE MODE buttons to their default settings, see "Resetting the REMOTE MODE Buttons". Note • If any other button than the colored buttons is pressed, the operation will be cancelled. • This operation cannot be done while the AV receiver is in Receiver mode or when Zone 2/3 is active. Remote Control Codes for Onkyo Components Connected via RI Onkyo components that are connected via V are controlled by pointing the remote controller at the AV receiver, not the component. This allows you to control components that are out of view, in a rack, for example. 1 Make sure the Onkyo component is connected with an V cable and an analog audio cable (RCA). See "Connecting Onkyo RI Components" for details (➔ page 23). 2 Enter the appropriate remote control code for a REMOTE MODE button, by referring to the previous section. ` 42157: Onkyo cassette tape deck with V ` 81993: Onkyo Dock with V 3 Press the REMOTE MODE button, point the remote controller at the AV receiver, and operate the component. Controlling Onkyo components without V If you want to control an Onkyo component by pointing the remote controller directly at it, or you want to control an Onkyo component that's not connected via V, use the following remote control codes: Controlling Other Components ` 30627: Onkyo DVD player without V ` 71817: Onkyo CD player without V ` 32900/33100/33500: Onkyo Blu-ray Disc player ` 32901/33104/33504: Onkyo HD DVD player ` 70868: Onkyo MD recorder without V ` 71323: Onkyo CD recorder without V ` 82990: Onkyo Dock without V Resetting the REMOTE MODE Buttons You can reset a REMOTE MODE button to its default remote control code. 1 While holding down the REMOTE MODE button that you want to reset, press and hold down HOME until the REMOTE MODE button lights (about 3 seconds). 2 Within 30 seconds, press the REMOTE MODE button again. The REMOTE MODE button flashes twice, indicating that the button has been reset. Each REMOTE MODE button is preprogrammed with a remote control code. When a button is reset, its preprogrammed code is restored. Note • The learning command is also reset. En-83

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
Controlling Other Components
En-83
Note
• Though the provided remote control codes are correct at
the time of release, they are subject to change.
You can change the configuration of colored buttons,
with which
REMOTE MODE
buttons are preset.
Tip
• To reset the
REMOTE MODE
buttons to their default
settings, see “Resetting the REMOTE MODE Buttons”.
Note
•
If any other button than the colored buttons is pressed, the
operation will be cancelled.
• This operation cannot be done while the AV receiver is in
Receiver mode or when Zone 2/3 is active.
Onkyo components that are connected via
u
are
controlled by pointing the remote controller at the AV
receiver, not the component. This allows you to
control components that are out of view, in a rack, for
example.
Controlling Onkyo components without
u
If you want to control an Onkyo component by
pointing the remote controller directly at it, or you
want to control an Onkyo component that’s not
connected via
u
, use the following remote control
codes:
30627
:
Onkyo DVD player without
u
71817
:
Onkyo CD player without
u
32900/33100/33500
:
Onkyo Blu-ray Disc player
32901/33104/33504
:
Onkyo HD DVD player
70868
:
Onkyo MD recorder without
u
71323
:
Onkyo CD recorder without
u
82990
:
Onkyo Dock without
u
You can reset a
REMOTE MODE
button to its default
remote control code.
3
Within 30 seconds, use the number buttons to
enter the 5-digit remote control code.
The
REMOTE MODE
button flashes twice.
If the remote control code is not entered
successfully, the
REMOTE MODE
button will
flash once slowly.
Remapping Colored Buttons
1
While holding down the REMOTE MODE
button that you want to program, press and
hold down A (Red) until the REMOTE MODE
button lights (about 3 seconds).
You can only change colored buttons for
components whose codes belong to categories
of the Remote Control Codes list (BD/DVD
player, TV, cable set-top box, etc).
2
Within 30 seconds, press the colored buttons
in the order that you want to reassign them.
The button presses are assigned to each button
from left to right. The
REMOTE MODE
button
flashes twice, indicating that the sequence has
been successfully assigned. If the sequence is
not successfully assigned, the
REMOTE MODE
button will flash once slowly.
Remote Control Codes for Onkyo
Components Connected via RI
1
Make sure the Onkyo component is connected
with an
u
cable and an analog audio cable
(RCA).
See “Connecting Onkyo RI Components” for
details (
➔
page 23
).
2
Enter the appropriate remote control code for
a REMOTE MODE button, by referring to the
previous section.
42157
:
Onkyo cassette tape deck with
u
81993
:
Onkyo Dock with
u
3
Press the REMOTE MODE button, point the
remote controller at the AV receiver, and
operate the component.
Resetting the REMOTE MODE Buttons
1
While holding down the REMOTE MODE
button that you want to reset, press and hold
down HOME until the REMOTE MODE button
lights (about 3 seconds).
2
Within 30 seconds, press the REMOTE MODE
button again.
The
REMOTE MODE
button flashes twice,
indicating that the button has been reset.
Each
REMOTE MODE
button is preprogrammed
with a remote control code. When a button is
reset, its preprogrammed code is restored.
Note
• The learning command is also reset.