Panasonic AW-UE4 Basic Operating Instructions - Page 18

Stand-alone installation, when the mount bracket is not going to be used

Get Panasonic AW-UE4 PDF manuals and user guides View all Panasonic AW-UE4 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 18 highlights

Installation Instructions Stand-alone installation (when the mount bracket is not going to be used)  When installing the unit on a desktop Place the unit flat on the surface. [Note]  Install the unit in a stable location which will not be susceptible to shaking. If the unit is installed in a location which is susceptible to shaking, this will cause the unit's images to shake in turn.  Take care not to allow the unit to fall or otherwise be damaged during installation.  When carrying the unit, do not hold it by its head.  Take care not to pull the connected cables. Doing so may cause the unit to fall and/or it may result in injury. Ensure that the unit will not fall off. Correct Incorrect  When mounting the unit on a tripod Attach the tripod to the threaded holes for mounting the camera on the camera's bottom panel. Place the tripod on a completely flat and level surface. Tighten the screws by hand to mount the tripod securely. Use screw for mounting tripod that satisfy the following standard. [Note]  Do not install the unit where people will be passing back and forth.  When using the unit mounted on a tripod, do not put the tripod high above the floor level.  Mount the unit securely so there is no looseness. Looseness may cause the unit to fall off and/or result in injuries.  When the unit is going to be used for a prolonged period of time, take steps to ensure that the unit will not topple or fall over and that it will not fall off or fall down. After using the unit, restore the installation location to its original state without delay. 18

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
18
Stand-alone installation
(when the mount bracket is not going to be used)
When installing the unit on a desktop
Place the unit flat on the surface.
[Note]
Install the unit in a stable location which will not be susceptible to shaking. If the unit is installed in a
location which is susceptible to shaking, this will cause the unit’s images to shake in turn.
Take care not to allow the unit to fall or otherwise be damaged during installation.
When carrying the unit, do not hold it by its head.
Take care not to pull the connected cables. Doing so may cause the unit to fall and/or it may result
in injury.
Ensure that the unit will not fall off.
Correct
Incorrect
When mounting the unit on a tripod
Attach the tripod to the threaded holes for mounting the camera on the camera’s bottom panel. Place
the tripod on a completely flat and level surface.
Tighten the screws by hand to mount the tripod securely.
Use screw for mounting tripod that satisfy the following standard.
[Note]
Do not install the unit where people will be passing back and forth.
When using the unit mounted on a tripod, do not put the tripod high above the floor level.
Mount the unit securely so there is no looseness. Looseness may cause the unit to fall off and/or
result in injuries.
When the unit is going to be used for a prolonged period of time, take steps to ensure that the unit
will not topple or fall over and that it will not fall off or fall down. After using the unit, restore the
installation location to its original state without delay.
Installation Instructions