Panasonic AW-UE4 Basic Operating Instructions - Page 66

For Windows, Symptom, Cause and solution

Get Panasonic AW-UE4 PDF manuals and user guides View all Panasonic AW-UE4 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 66 highlights

Symptom Cannot access from a web browser Cause and solution Has a valid IP address been set in the unit? Has the wrong IP address been accessed? → Check the connections by following the steps below. For Windows: Using the Windows command prompt, execute > ping [IP address which has been set in the camera] A reply returned from the unit signifies that there are no problems in operation. If a reply is not received, try following operation: Reboot the unit, and within 20 minutes change the IP address using the Easy IP Setup Software. For Mac: Using the OS X terminal, execute > ping -c 10 [IP address which has been set in the camera] A reply returned from the unit signifies that there are no problems in operation. If a reply is not received, try following operation: Reboot the unit, and within 20 minutes change the IP address using the Easy IP Setup Software. Is the same IP address setting being used by another unit? → Check out the IP addresses of the unit, access devices (personal computer, etc.) and any other cameras. Does the subnet mask setting match the network subnet of the connection destination? → Check out the subnet mask settings of the unit and access devices, and then consult with the network administrator. Has the "Use a proxy server" setting been selected by the web browser? (When the unit and the personal computer are connected to the same subnet) → If a proxy server has been set using the [proxy setting] of the web browser, it is recommended that a "Don't use proxy" address be selected as the unit's IP address setting. Has the wrong default gateway been set for the unit? (When the unit and personal computer are connected to different subnets) → Check out the default gateway that has been set for the unit, and then consult with the network administrator. 66

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
66
Symptom
Cause and solution
Cannot access from a web
browser
Has a valid IP address been set in the unit?
Has the wrong IP address been accessed?
→ Check the connections by following the steps below.
For Windows:
Using the Windows command prompt, execute
> ping [IP address which has been set in the camera]
A reply returned from the unit signifies that there are no problems in
operation.
If a reply is not received, try following operation:
Reboot the unit, and within 20 minutes change the IP address using
the Easy IP Setup Software.
For Mac:
Using the OS X terminal, execute
> ping -c 10 [IP address which has been set in the camera]
A reply returned from the unit signifies that there are no problems in
operation.
If a reply is not received, try following operation:
Reboot the unit, and within 20 minutes change the IP address using
the Easy IP Setup Software.
Is the same IP address setting being used by another unit?
→ Check out the IP add
resses of the unit, access devices (personal
computer, etc.) and any other cameras.
Does the subnet mask setting match the network subnet of the
connection destination?
→ Check out the subnet mask settings of the unit and access
devices, and then consult with the network administrator.
Has the “Use a proxy server” setting been selected by the web
browser? (When the unit and the personal computer are
connected to the same subnet)
→ If a proxy server has been set using the [proxy setting] of the web
brows
er, it is recommended that a “Don’t use proxy” address be
selected as the unit’s IP address setting.
Has the wrong default gateway been set for the unit? (When the
unit and personal computer are connected to different
subnets
)
→ Check out the default gat
eway that has been set for the unit, and
then consult with the network administrator.