Panasonic HC-X1000 HC-X1000 Owner's Manual (English) - Page 42

Troubleshooting

Page 42 highlights

Others Troubleshooting ∫ It is not a malfunction in following cases The lens, the viewfinder or ≥ This is due to condensation. It is not a malfunction. Please LCD monitor fog up. refer to page 9. Object seems to be warped. ≥ Object seems to be warped slightly when the object moves across the image very fast, but this is because the unit is using MOS for the image sensor. This is not a malfunction. Problem This unit cannot be turned on. This unit does not stay on long enough. Battery runs down quickly. This unit cannot be operated though it is turned on. This unit does not operate normally. The unit arbitrarily stops recording. Color or brightness of the image changes, or you may see horizontal bars in the image. The LCD monitor flickers indoors. Check points ≥ Charge the battery again to ensure it is sufficiently charged. (l 20) ≥ In cold places, the battery using time becomes shorter. ≥ The battery has a limited life. If the operating time is still too short even after the battery is fully charged, the battery has worn out and needs to be replaced. ≥ Remove the battery or AC adaptor, wait about 1 minute and then reconnect the battery or AC adaptor. Then about 1 minute later, turn on the unit again. (Conducting the above operation while the media is being accessed may damage the data on the media.) ≥ If normal operation is still not restored, detach the power connected, and consult the dealer who you purchased this unit from. ≥ Use an SD card that can be used for motion picture recording. (l 23) ≥ The recordable time may have shortened due to the deterioration of the data writing speed or repeated recording and deletion. Using the unit, format the SD card. (l 29) ≥ Color or brightness of the image may change, or you may see horizontal bars in the image when the object is recorded under fluorescent light, mercury light or sodium light, etc., but this is not a malfunction. ≥ Record images in Intelligent Auto Mode or adjust the shutter speed to 1/50, 1/60 or 1/100. ≥ Adjust the Synchro Scan shutter speed. Please refer to "Owner's Manual (PDF format)" for details. 42 SQT0477 (ENG)

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54

42
SQT0477 (ENG)
It is not a malfunction in following cases
Please refer to “Owner’s Manual (PDF format)” for details.
Others
Troubleshooting
The lens, the viewfinder or
LCD monitor fog up.
This is due to condensation. It is not a malfunction. Please
refer to page 9.
Object seems to be warped.
Object seems to be warped slightly when the object moves
across the image very fast, but this is because the unit is using
MOS for the image sensor. This is not a malfunction.
Problem
Check points
This unit cannot be turned
on.
This unit does not stay on
long enough.
Battery runs down quickly.
Charge the battery again to ensure it is sufficiently charged.
(
l
20)
In cold places, the battery using time becomes shorter.
The battery has a limited life. If the operating time is still too
short even after the battery is fully charged, the battery has
worn out and needs to be replaced.
This unit cannot be
operated though it is
turned on.
This unit does not operate
normally.
Remove the battery or AC adaptor, wait about 1 minute and
then reconnect the battery or AC adaptor. Then about
1 minute later, turn on the unit again. (Conducting the above
operation while the media is being accessed may damage the
data on the media.)
If normal operation is still not restored, detach the power
connected, and consult the dealer who you purchased this
unit from.
The unit arbitrarily stops
recording.
Use an SD card that can be used for motion picture recording.
(
l
23)
The recordable time may have shortened due to the
deterioration of the data writing speed or repeated recording
and deletion. Using the unit, format the SD card. (
l
29)
Color or brightness of the
image changes, or you
may see horizontal bars in
the image.
The LCD monitor flickers
indoors.
Color or brightness of the image may change, or you may see
horizontal bars in the image when the object is recorded
under fluorescent light, mercury light or sodium light, etc., but
this is not a malfunction.
Record images in Intelligent Auto Mode or adjust the shutter
speed to 1/50, 1/60 or 1/100.
Adjust the Synchro Scan shutter speed.