Panasonic KX-HNC805 Installation Guide - Page 23

Registering the camera to your hub

Get Panasonic KX-HNC805 PDF manuals and user guides View all Panasonic KX-HNC805 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 23 highlights

Setup Registering the camera to your hub Do not perform this procedure if you are using the camera by itself (i.e., you do not have a KX-HNB600 hub). Use the initial setup procedure (page 18). If you want to integrate your HD camera with a Panasonic Home Network System, you must register the camera to the hub. Registering the camera Confirm the following before you begin. - Make sure you can use your mobile device to access the hub - Make sure the hub's firmware is up to date and that you are using the latest version of the [Home Network] app. For more information, refer to the System Setup Guide included with your hub and the User's Guide (page 30). 1 Plug in the camera and wait about 1 minute for the camera's LED to light in green. R If the LED does not light in green, or if you experience trouble during this procedure, reset the camera (page 24) and then repeat this procedure. 2 Start the [Home Network] app. 3 From the [Home Network] app home screen, tap [Settings]. 4 Tap [Device Registration] ® [Registration] ® [HD Camera] ® [Method 1]. 5 When prompted, press the MSETUPN button on the back of the camera. R The camera registers your mobile device. R The app's home screen is displayed when registration is complete. 6 Follow the on-screen instructions. When prompted, set the password that will be used to access the camera. Note: R When registration is complete, the hub sounds one long beep. R If registration fails, the hub sounds several short beeps. For assistance, visit www.panasonic.ca/english/support 23 HNC805C_(en_en)_0902_ver.110.pdf 23 2016/09/05 13:39:11

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
Registering the
camera to your hub
Do not perform this procedure if
you are using the camera by
itself (i.e., you do not have a
KX-HNB600 hub). Use the initial
setup procedure (page 18).
If you want to integrate your HD
camera with a Panasonic Home
Network System, you must
register the camera to the hub.
Registering the camera
Confirm the following before you
begin.
–
Make sure you can use your
mobile device to access the hub
–
Make sure the hub’s firmware is
up to date and that you are
using the latest version of the
[Home Network]
app.
For more information, refer to
the System Setup Guide
included with your hub and the
User’s Guide (page 30).
1
Plug in the camera and wait
about 1 minute for the
camera’s LED to light in green.
R
If the LED does not light in
green, or if you experience
trouble during this
procedure, reset the
camera (page 24) and
then repeat this procedure.
2
Start the
[Home Network]
app.
3
From the
[Home Network]
app home screen, tap
[Settings]
.
4
Tap
[Device Registration]
®
[Registration]
®
[HD
Camera]
®
[Method 1]
.
5
When prompted, press the
M
SETUP
N
button on the back
of the camera.
R
The camera registers your
mobile device.
R
The app’s home screen is
displayed when registration
is complete.
6
Follow the on-screen
instructions. When prompted,
set the password that will be
used to access the camera.
Note:
R
When registration is complete,
the hub sounds one long beep.
R
If registration fails, the hub
sounds several short beeps.
For assistance, visit www.panasonic.ca/english/support
23
Setup
HNC805C_(en_en)_0902_ver.110.pdf
23
2016/09/05
13:39:11